Jump to content
SAU Community

The Complete Ethanol Thread

Cowboy1600

By Cowboy1600,
in Engines & Forced Induction

 Share

Recommended Posts

  • 8 months later...
  • Replies 159
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Hanaldo
Hanaldo

Hey all, Just wanted to ask a quick one about fuel filters. What are you guys using these days? I've read a number of older posts about using the standard Ryco filters, some good some bad. I'm also a

NYTSKY
NYTSKY

I fill my car up at my local United. Give it a blast in 3rd gear, if AFRs are between 11.2 and 11.8 keep thrashing.

discopotato03
discopotato03

I reckon that if tuners like reliable engines the only way you'll ever get a good flex tune is blending low octane ULP with ethanol . Hard to imagine Caltex and United using 98 PULP in their E70/E85 p

Hanaldo Grand Master

Hanaldo

Posted
Posted

Hey all,

Just wanted to ask a quick one about fuel filters. What are you guys using these days? I've read a number of older posts about using the standard Ryco filters, some good some bad. I'm also aware of the situation with needing to replace fuel filters regularly just after switching to E85 until the system is clean. So right now I'm considering three paths.

1. I stick with the Ryco paper filter and just replace it regularly.

2. I stick with the Ryco paper filter for now, then after my first tank of E85, switch to a billet filter (Aeroflow, Speedflow, Proflow, or similar?)

3. I switch to a billet filter now, before getting the E85 tune.

At the moment I'm leaning towards option 3 for a couple of reasons. Firstly I have the standard feed line to my Ryco filter, then a -6 fuel line to my HKS rail. It works, but considering the Ryco filter has 5/16 push on barbs, it doesn't quite fit as nicely as I would like. With the billet filter I could use a -6 AN fitting on one side, and a -6 AN to 5/16 tail barb on the other side. Second, if I need to replace filters regularly, would a washable element not be a cost effective solution?

  • Like 1
scotty nm35 Grand Master

scotty nm35

Posted
Posted

I use twin -6 an stainless mesh filters, Proflow ones, they cost around $100 each though plus fittings. No issues in 3 years daily driving on United mainly, and they have never been cleaned.

Hanaldo Grand Master

Hanaldo

Posted
Posted

Do you know what micron filter element you've got, Scott?

Another one, where are people mounting their GM flex-fuel sensors? I've got the flow through type and I thought I could mount it between my regulator and return line in the engine bay, but I can't see it happening. This thing is quite hard to mount with the factory hard lines :glare:

Piggaz Grand Master

Piggaz

Posted
Posted

Do you know what micron filter element you've got, Scott?

Another one, where are people mounting their GM flex-fuel sensors? I've got the flow through type and I thought I could mount it between my regulator and return line in the engine bay, but I can't see it happening. This thing is quite hard to mount with the factory hard lines :glare:

In the boot. Tee off the return line just before it drops back into the tank. Hidden sensor FTW!

Hanaldo Grand Master

Hanaldo

Posted
Posted (edited)

In the boot. Tee off the return line just before it drops back into the tank. Hidden sensor FTW!

Yeh? I did think of putting it there. Could maybe work something out... All seems a bit tight though, I can hardly see my return line let alone find a place to put two tees into it :/

Edited by Hanaldo
Piggaz Grand Master

Piggaz

Posted
Posted

Yeh? I did think of putting it there. Could maybe work something out... All seems a bit tight though, I can hardly see my return line let alone find a place to put two tees into it :/

BRB, taking a photo for you :P

Piggaz Grand Master

Piggaz

Posted
Posted

I think it's 100 micron mesh.

Don't you want the sensor as close to the rail as possible?

I can't see how it makes any difference. Either way, once the fuel is mixed, it's the same. Just dontn belt it until you see the reading settle.
Hanaldo Grand Master

Hanaldo

Posted
Posted

Ah, you got the little small thing.

Yeh so they say. Its fkn massive! Ideally I would mount it close to the rail, but I can't see it fitting anywhere unless I remote mount the sensor and run like 2 meters of hose to it :/

Piggaz Grand Master

Piggaz

Posted
Posted

Yeh so they say. Its fkn massive! Ideally I would mount it close to the rail, but I can't see it fitting anywhere unless I remote mount the sensor and run like 2 meters of hose to it :/

Under the car?

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

Just curious why I've seen a few setups with the flex sensor mounted in the boot? Another car I've seen setup by UNIGROUP has the flex sensor in the boot too?

What are the benefits? Is it just a convenience thing or heat stress thing?

Piggaz Grand Master

Piggaz

Posted
Posted

Just curious why I've seen a few setups with the flex sensor mounted in the boot? Another car I've seen setup by UNIGROUP has the flex sensor in the boot too?

What are the benefits? Is it just a convenience thing or heat stress thing?

It's one less thing in an already full engine bay. No other reason.
Piggaz Grand Master

Piggaz

Posted
Posted

How many free 0-5V inputs do you need on your ecu? The zeitronix Eca kit outputs fuel temp and ethanol % doesn't it?

1 I'm pretty sure. And yes fuel temp too. You can set up fuel temp correction too

Hanaldo Grand Master

Hanaldo

Posted
Posted

Under the car?

Yeh this is what I was thinking of. It would be so much easier if I could cut the standard hard line, but I don't want to lose the flared end.

I think the easiest thing would just be to run a longer length of hose to the sensor. Just seems such a messy way of doing it :/

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • Kinkstaah
      My BMW 335i

      By Kinkstaah · Posted

      I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      D2 and Ksport are essentially the same thing and basically just generic Taiwanese manufacture. Better than ChinaBay crap, but... not top shelf. Öhlins have got to be some of the best dampers around, so likely to be a good option. It's going to get to the point though where I suggest you buy from Oz. We have at least 2x excellent options here. If I were you though, I'd be talking to KW about doing something for the R33. There's bugger all difference between that and the 32. In GTR land, anyway.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      KW only offers a set for the R32 GTR. Popular options are D2 racing, Ksport or Öhlins. I have a D2 Racing coilover set, though I don't know for sure which one.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Well, the good news is you have more than one very good option for new coilovers in and around your country. Worth the drive over to KW to talk about GTR stuff.
×
×
  • Create New...