Jump to content
SAU Community

Recommended Posts

I'm currently trying to figure out what would be best suited out of these two sizes but I don't really have my head around offsets too well.

I want the wheels to be a flush fit with the guards, not tucked in and not hanging out. Can anyone confirm if either of these sizes are correct?

18x10+20 or 18x9.5+22

If you have either of these sizes on your 32 I would be grateful if you could post close up pics of how they fit in the guards.

Edited by NISMATT
Link to comment
https://www.sau.com.au/forums/topic/405555-correct-wheel-size-r32-gtr/
Share on other sites

They sit fine now but I have a 5mm spacer as the fronts rubbed the inside tyre wall without it, they came with the car and I have no idea what their offset is unfortunately.

So if +12 is dead flush, is +20 sitting in or out the guards?

  • 2 weeks later...

I've got 18x10 +18 with my front and rear guards have been rolled and worked on. And it works perfect

Alright Deano any chance you could post some pics up for me so I know where they will be roughly?

Just super keen to know exactly how they will sit before I lay down nearly 4K.

Hi Matt, I run 18x9.5 +12 and they sit flush. (Tyres are 255/35/R18).

265's will scrub on the front but very minor on lock going slow.

I'll get some pics today

As per your first post

18x9.5 +22 will sit 10mm further in.

18x10 +20 will sit 2mm further in

Deano's 18x10 +18 will sit exactly the same as mine.

18x10 +20 will sit 2mm further in

Hope some of the snaps help your choice

Richard thanks for the thorough response that was just what I was looking for.

Your fitment is pretty much spot on what I'm after so 2mm further in the guards I'll be stoked with, I run 255's on 10 inch wheels now so that's what I'll be using on the new rims.

  • 3 months later...

I am running CE28's 18x9.5 +15 with 265's all round.

Heaps of room! I could drive a truck through that guard gap.

I think a +12 would be better or a 18x10.5

(Uneven ground)

Side.jpg

Fronts.jpg

Rear.jpg

Edited by DarrenJC
  • Like 1

Hi guys I'm new to this forum and new to Skyline ownership. I've recently brought a 32 gtr and am looking to put new wheels on it but have a couple of questions I hope someone on here can help me with:

1. Will 19 x 9.5 +30 fit under the guards and clear the struts, or will there need to be some modifications done?

2. Does any one know how much a standard rim weighs? ( no tyre )

Unfortunately the car is not at my house so I can't measure distances etc and like many haven't quite grasped the offset concept yet.

I assume because the standard (16x8 +30) are the same offset as the rims I'm looking at that, they will just be .75 inch closer to the strut and the guard?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...