Jump to content
SAU Community

Recommended Posts

I'm currently trying to figure out what would be best suited out of these two sizes but I don't really have my head around offsets too well.

I want the wheels to be a flush fit with the guards, not tucked in and not hanging out. Can anyone confirm if either of these sizes are correct?

18x10+20 or 18x9.5+22

If you have either of these sizes on your 32 I would be grateful if you could post close up pics of how they fit in the guards.

Edited by NISMATT
Link to comment
https://www.sau.com.au/forums/topic/405555-correct-wheel-size-r32-gtr/
Share on other sites

They sit fine now but I have a 5mm spacer as the fronts rubbed the inside tyre wall without it, they came with the car and I have no idea what their offset is unfortunately.

So if +12 is dead flush, is +20 sitting in or out the guards?

  • 2 weeks later...

I've got 18x10 +18 with my front and rear guards have been rolled and worked on. And it works perfect

Alright Deano any chance you could post some pics up for me so I know where they will be roughly?

Just super keen to know exactly how they will sit before I lay down nearly 4K.

Hi Matt, I run 18x9.5 +12 and they sit flush. (Tyres are 255/35/R18).

265's will scrub on the front but very minor on lock going slow.

I'll get some pics today

As per your first post

18x9.5 +22 will sit 10mm further in.

18x10 +20 will sit 2mm further in

Deano's 18x10 +18 will sit exactly the same as mine.

18x10 +20 will sit 2mm further in

Hope some of the snaps help your choice

Richard thanks for the thorough response that was just what I was looking for.

Your fitment is pretty much spot on what I'm after so 2mm further in the guards I'll be stoked with, I run 255's on 10 inch wheels now so that's what I'll be using on the new rims.

  • 3 months later...

I am running CE28's 18x9.5 +15 with 265's all round.

Heaps of room! I could drive a truck through that guard gap.

I think a +12 would be better or a 18x10.5

(Uneven ground)

Side.jpg

Fronts.jpg

Rear.jpg

Edited by DarrenJC
  • Like 1

Hi guys I'm new to this forum and new to Skyline ownership. I've recently brought a 32 gtr and am looking to put new wheels on it but have a couple of questions I hope someone on here can help me with:

1. Will 19 x 9.5 +30 fit under the guards and clear the struts, or will there need to be some modifications done?

2. Does any one know how much a standard rim weighs? ( no tyre )

Unfortunately the car is not at my house so I can't measure distances etc and like many haven't quite grasped the offset concept yet.

I assume because the standard (16x8 +30) are the same offset as the rims I'm looking at that, they will just be .75 inch closer to the strut and the guard?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...