Jump to content
SAU Community

Recommended Posts

I'm currently trying to figure out what would be best suited out of these two sizes but I don't really have my head around offsets too well.

I want the wheels to be a flush fit with the guards, not tucked in and not hanging out. Can anyone confirm if either of these sizes are correct?

18x10+20 or 18x9.5+22

If you have either of these sizes on your 32 I would be grateful if you could post close up pics of how they fit in the guards.

Edited by NISMATT
Link to comment
https://www.sau.com.au/forums/topic/405555-correct-wheel-size-r32-gtr/
Share on other sites

They sit fine now but I have a 5mm spacer as the fronts rubbed the inside tyre wall without it, they came with the car and I have no idea what their offset is unfortunately.

So if +12 is dead flush, is +20 sitting in or out the guards?

  • 2 weeks later...

I've got 18x10 +18 with my front and rear guards have been rolled and worked on. And it works perfect

Alright Deano any chance you could post some pics up for me so I know where they will be roughly?

Just super keen to know exactly how they will sit before I lay down nearly 4K.

Hi Matt, I run 18x9.5 +12 and they sit flush. (Tyres are 255/35/R18).

265's will scrub on the front but very minor on lock going slow.

I'll get some pics today

As per your first post

18x9.5 +22 will sit 10mm further in.

18x10 +20 will sit 2mm further in

Deano's 18x10 +18 will sit exactly the same as mine.

18x10 +20 will sit 2mm further in

Hope some of the snaps help your choice

Richard thanks for the thorough response that was just what I was looking for.

Your fitment is pretty much spot on what I'm after so 2mm further in the guards I'll be stoked with, I run 255's on 10 inch wheels now so that's what I'll be using on the new rims.

  • 3 months later...

I am running CE28's 18x9.5 +15 with 265's all round.

Heaps of room! I could drive a truck through that guard gap.

I think a +12 would be better or a 18x10.5

(Uneven ground)

Side.jpg

Fronts.jpg

Rear.jpg

Edited by DarrenJC
  • Like 1

Hi guys I'm new to this forum and new to Skyline ownership. I've recently brought a 32 gtr and am looking to put new wheels on it but have a couple of questions I hope someone on here can help me with:

1. Will 19 x 9.5 +30 fit under the guards and clear the struts, or will there need to be some modifications done?

2. Does any one know how much a standard rim weighs? ( no tyre )

Unfortunately the car is not at my house so I can't measure distances etc and like many haven't quite grasped the offset concept yet.

I assume because the standard (16x8 +30) are the same offset as the rims I'm looking at that, they will just be .75 inch closer to the strut and the guard?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...