Jump to content
SAU Community

Help With Re-Building R32 Gtr Rear Diff With Nismo 3843S-Rs521 Disk Kit....

Ramius83
 Share

Recommended Posts

Ramius83 Collaborator

Ramius83

Posted
Posted

I need some help with re-building the R32 GTR rear diff with the NISMO 3843S-RS521 disk kit. Of course, all of the instructions are in Japanese. Contacted NISMO here in the States and they are of no help. I never actually tested the break-away torque of the old setup, I just bought this diff used so I thought, hey, why not.

Tore apart the diff and the basket components and installed the disks how it appeared in the diagram. Put everything back together, except no fluid, rigged up a break-away tester, and found it to be absolutely zero ft/lbs break-away.

So, now I am thinking about how we assembled the disks and the one thing that I may have omitted that I shouldn't have. In the OEM form, each clutch disk stack is comprised of 6 disks and one large shim that is on the outside of the stack. We removed all 6 disks and the one large shim that is pictured below, installed the new small shim and all 6 new disks. Did the same for the other side, and put it all back together. Obviously, now there is no break-away torque. Does this large shim need to go back in the casing on both sides?

imag0215w.jpg

imag0216au.jpg

Any help would be greatly appreciated. Thanks......

The Dan Grand Master

The Dan

Posted
Posted

I need some help with re-building the R32 GTR rear diff with the NISMO 3843S-RS521 disk kit. Of course, all of the instructions are in Japanese. Contacted NISMO here in the States and they are of no help. I never actually tested the break-away torque of the old setup, I just bought this diff used so I thought, hey, why not.

Tore apart the diff and the basket components and installed the disks how it appeared in the diagram. Put everything back together, except no fluid, rigged up a break-away tester, and found it to be absolutely zero ft/lbs break-away.

So, now I am thinking about how we assembled the disks and the one thing that I may have omitted that I shouldn't have. In the OEM form, each clutch disk stack is comprised of 6 disks and one large shim that is on the outside of the stack. We removed all 6 disks and the one large shim that is pictured below, installed the new small shim and all 6 new disks. Did the same for the other side, and put it all back together. Obviously, now there is no break-away torque. Does this large shim need to go back in the casing on both sides?

imag0215w.jpg

imag0216au.jpg

Any help would be greatly appreciated. Thanks......

I would say try it with them in and see what you get. If you can put it all back together 'relatively' easily with the two old shims then it should be right. There is a bit of preload on those.

I can't remember the exact breakaway torque but the number 60ft/lbs keeps springing to mind. I'll see if I can find it in my folders

Ramius83 Collaborator

Ramius83

Posted
  • Author
Posted

Yeah, that is what we were thinking too. It isn't hard to take it all apart again, just wanted to make sure that before we do, we somewhat have more of an idea lol.

Ramius83 Collaborator

Ramius83

Posted
  • Author
Posted

Ok, so we threw the factory shims/spacers in with the whole stack. with everything put together, we are getting about 110 ft/lbs break-away. Obviously this will change/decrease with some amount of driving. But nonetheless, now we are getting some break-away. Does this sound OK?

The Dan Grand Master

The Dan

Posted
Posted

Yep. That sounds ok. Let us know how tight that is to begin with please.

You'll need to go out and do figure 8's in a culdesac somewhere to bed in the clutch plates. Usually 15minutes or so is enough.

Ramius83 Collaborator

Ramius83

Posted
  • Author
Posted

There was also a 1.85mm friction disk that was included with the kit, I guess for differences in stack height. We left that one out and just threw all the 1.75mm friction disks in. I would assume that the larger disk would increase the break-away torque, which may result in a clunkier diff in parking lots and such. After I get the car running, I'll let everyone know it was successful or a failure lol......

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

    • davemoto63
      My new to me M35 Stagea wagon

      By davemoto63 · Posted

      Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Yeah the rule of thumb with an LS is 7psi per 1000rpm. That is decidedly not enough at 6800rpm. I mainly looked for the scenarios where knock started to be picked up and it was later in the session when things were hotter, and oil was thinner, and the pressure was lower than it should be. (i.e very horrible). I am hoping with thicker oil (I was running Penrite ten tenths 10-40, the manual specifies 10-30) that does not leak that it's much improved at that time!!! I am using Project Mu Club Racer CR pads. I'm also using the Project Mu 335C fluid. The symptoms imply that it was fluid that boiled, but no bubbles seemed pretty weird to me when I bled it today. I want to try Castrol SRF as it has a much higher wet temp but, well, I have new Project Mu fluid lol... so I should at least use that. The pedal on track was really noticable. It went from basically normal feeling to instantly near-floor. The car did pull up as before, it was just very much nearly at the floor before the brakes engaged. At that point I pretty much decided the day was very done, it did *kinda* come back during that very slow cooldown lap into the pits. Felt perfectly fine driving home.
    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      f**king around with the bro
×
×
  • Create New...