Jump to content
SAU Community

Recommended Posts

Hi im new here, and i am looking at purchasing an r32 GT-R. I am 22, and have gotten sick of driving around in a manual v6 commodore. Time to upgrade to the ultimate car! Now i will be taking a loan out on the car.

My budget will be around $18000. (Not including insurance) i have found one which i will go check out, but what i would like to know is, how are the majority of them running these days? Are they needing rebuilds? This one i will look at claims the engine was rebuilt in 2003.

The last thing i need is to take out a loan and then have to take more money out to fix it up. I would just like some of your thoughts as i am also considering an s15. Thanks!

Link to comment
https://www.sau.com.au/forums/topic/412132-r32-gt-rs/
Share on other sites

As they're old cars, there's bound to be issues.

I purchased one 2 years ago and spent a fair bit of coin getting it perfect.

Major things to look for are:

Functioning 4x4 - You'll be surprised how many don't...

Diffs sound mickey

Rusting

Healthy RB (get an expert, never rely on yourself)

Good gearbox

Clutch

No major leaking in the engine bay

Good luck mate... once you go R it'll be hard going back ;)

Link to comment
https://www.sau.com.au/forums/topic/412132-r32-gt-rs/#findComment-6591084
Share on other sites

22 years old and getting an $18K loan to buy the most commonly thrashed 18-23 year old car in the world.

What could possibly go wrong?

I was 20 when I got a loan for 20k for my R32 GTR nearly 2 years ago. Haven't had any problems (knock wood). All I have had to do is general maintenance.

Link to comment
https://www.sau.com.au/forums/topic/412132-r32-gt-rs/#findComment-6591661
Share on other sites

Two things:

Never borrow money to purchase an "asset" that depreciates, eg a car. It s a mugs game.

Second:

Dont use a GTR for a daily. They are hopeless at it.

Summary:

Save your coin until you can afford to keep a good GTR as a second car.

^^part agree with the above, not every one who borrows money to buy a car expects good resale or as an investment . . .i borrowed money to buy a 34 skyline cos i f*kn like driving them

Link to comment
https://www.sau.com.au/forums/topic/412132-r32-gt-rs/#findComment-6593689
Share on other sites

Two things:

Never borrow money to purchase an "asset" that depreciates, eg a car. It s a mugs game.

This!

Second:

Dont use a GTR for a daily. They are hopeless at it.

I used mind as a daily for about 3 years.

It's do-able but better with a stock clutch and softer suspension if you have aftermarket coilovers.

Summary:

Save your coin until you can afford to keep a good GTR as a second car.

This!

Link to comment
https://www.sau.com.au/forums/topic/412132-r32-gt-rs/#findComment-6594384
Share on other sites

  • 3 weeks later...

better idea...

but still.... loan for a car is not something I would ever do.

Everyones different.

not everyone has there parents to buy them a car

or

unable to wait the time necessary to save for a car as they many need it for work.

Birdspeed13 buy what you want...just act responsibility

Link to comment
https://www.sau.com.au/forums/topic/412132-r32-gt-rs/#findComment-6624910
Share on other sites

Good point.. what profession requires a GTR or S15?

So true. This cars are weekend toys if you ask me.

If you can afford a GTR as a daliy, you can afford a to keep it as a toy and buy another car for a daily.

Know I bet people with say to me i have used as a daily or am using as a daily now, like the post earlier but if i asked ya honestly, was it affordable?

Deep down we all know that could hardly be the case

Link to comment
https://www.sau.com.au/forums/topic/412132-r32-gt-rs/#findComment-6625634
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...