Jump to content
SAU Community

Recommended Posts

hey guys, long version of the story is,

i am about to upgrade the turbos on my 34 gtr to -5's and i am interested in having the exhaust manifolds port matched, extrude honed and ceramic coated. having said that i would like to have it all there and ready to swap over when i do it. question is, i have access to a pair of r33gtr turbo manifolds so was going to get them modified if there were the same and then just swap them over. if not i will just source a pair of 34's from somewhere but if they are the same it will save me some money and time.

cheers adam

i have access to a pair of r33gtr turbo manifolds so was going to get them modified if there were the same and then just swap them over.

To answer the question - Same mate.

Go and get 33 ones sorted out :thumbsup:

From what people who have done back to back dyno testing with a stock manifold vs ported manifold I've spoken to, have said they've lost response getting rid of the lip (porting) because exhaust velocity was reduced, whereas keeping the lip does act as a restriction when your power target is beyond the 350kw mark. Some workshops have confirmed this when I've contacted them, they even recommend keeping the stock manifolds as they are for -9 (GT-SS) & -7 (N1) turbos for response.

How about stock vs ported on -10s going for over 400kw? Would getting it all ceramic coated help with boost threshold?

Don't need -10's for over 400. Sort your setup out and have some "response" under 5500.

From what people who have done back to back dyno testing with a stock manifold vs ported manifold I've spoken to, have said they've lost response getting rid of the lip (porting) because exhaust velocity was reduced, whereas keeping the lip does act as a restriction when your power target is beyond the 350kw mark. Some workshops have confirmed this when I've contacted them, they even recommend keeping the stock manifolds as they are for -9 (GT-SS) & -7 (N1) turbos for response.

I agree with this, but it should be noted that Nissan supplied an essential ported manifold for N1 engines (r34 at least anyways)..which may indicate they started seeing restriction at much lower power levels.

manifoldoutlets.jpg

Edited by wedge_r34gtr
  • 2 months later...

Ok, to extend on this.

I have recieved my turbos and the manifolds too. Just waiting on my hpi dumps before sending them all away to be coated. My question now is, i initially was going to get unique autosport to extrude hone and port match them. Is there someone else i should go through or are they the goods when it comes to this. In their advert they say they port them to the gaskets but is there really any need to go bigger than the turbo flange? I have no intention of porting the turbo housings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...