Jump to content
SAU Community

Recommended Posts

Hey guys, I've got a R34 GTT and it has a varex exhaust system on it, the kind that is supposed to close a butterfly within the cannon and make the exhaust quiet at the press of a button.

Anyways, i bought it with the exhaust already on the car, and the power for the box controlling the butterfly wasn't connected, so i couldn't test it out.

I connected everything up after buying it and as always, turns out it wasn't connected for a reason, the butterfly in the exhaust doesn't open or close when i use the remote.

Pretty much there is power from the battery going to a small black box which is placed in the boot. from that box another set of wires connect to the cannon end of the exhaust.

I've checked the battery on the remotes and everything and it still doesnt work.

Does anyone have any suggestions on things i should do or check?

Thanks heaps guys

Link to comment
https://www.sau.com.au/forums/topic/415019-varex-exhaust-connection-question/
Share on other sites

Might be a bit of a pain but can you put battery power directly on the motor for the butterfly. That will tell you for sure if its dead

X-force are pretty good to deal with and should help you out with replacement parts

Varex mufflers... pretty good exhausts. Not something that belongs in the same sentence. They've been reported to be restrictive even when the butterfly has been fully open, not to mention illegal anyway.

thanks callan, should i just take the two wires that go to the motor and connect them directly to the power? how will the butterfly know when to open and when it should close though?

moodles, they aren't illegal, thats what a lot of people believe though. im sure about this as i actually looked into it, and ive gotten this car through a check after getting a defect for noise pollution, and they let me through it with the varex exhaust when it was closed.

thanks callan, should i just take the two wires that go to the motor and connect them directly to the power? how will the butterfly know when to open and when it should close though?

moodles, they aren't illegal, thats what a lot of people believe though. im sure about this as i actually looked into it, and ive gotten this car through a check after getting a defect for noise pollution, and they let me through it with the varex exhaust when it was closed.

Email Varex and ask them for a replacement control box perhaps? It could be the remote too I guess.

Hooking direct power to the motor will fu*k it.

I've seen it done where voltage was applied to the motor to test it. Reverse the polarity makes it go the other way. This may have been done acoss the circuit board so not sure if it was full 12v

They are restrictive closed but not to bad when they are open. The one I saw wouldn't make full boost closed but open it was fine

It wont damage it. I was running mine through a switch in the dash for 6 month with frequent use and never had a single problem. Just hook the power wire power wire to one side and touch the negative on the other. If it moves then its not the motor if it doesnt try swapping the wires around. Still doesnt work it could be the remote or control unit. Does the light come on the remote when a button is pressed?

so do i use the control box at all? or do i cut the wires and just hook up the cannon and motor directly to power without the control box?

and yeah the remote's light comes on and everything

Theres a way to do it by bridging curcuits on the circuit board, but i wouldnt recommend doing this if you dont have the wiring diagram or an understanding of electronics.

There should be a plug that goes to the motor from what I remember, if its a 2 pin plug, you cant go wrong, positive one side, negative the other, reverse polarity will make it spin the other way.

To test the motor you dont need the control box. Just get 2 pieces of wire connect one to the positive of your battery and one to the negative then connect the other ends of the wire to the terminals of the plug coming from the motor. And reverse the wires to go the other way.

I had one fitted to my falcon not too long ago, I just had mine dynod on the weekend.

Valve open: 198.9rwkw

Closed : 138.0rwkw

When open there was no restriction at all compared to my previous straight through muffler. This was with a full 3" system and a very big cam.

They feel very gutless when closed. I would only use it when you really need to be quiet.

ive looked into it a bit more, and i really cant figure out what the problem is, and im a bit hesitant to apply 12v directly to the motor without any resistors or fuses in between, just not willing to risk blowing the motor (if its not already blown)

i called up a shop near by and they said they'll have a look at it and diagnose the problem for free. guess thats worth a go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...