Jump to content
SAU Community

Recommended Posts

FB_IMG_13983840076175163_zpsmzxzi8xb.jpg

There it sat for a while.

IMG_299311822436500_zpszdyegxqq.jpeg

Went to the track a few times.

IMG_299266359881567_zpsw0t4nvg5.jpeg

Did alot of this for the hell of it.

20140613_211825_zpshztvzhpv.jpg

Found this afterwards

20140511_125815_zpsq6wr6ukp.jpg

Turns out i burnt the floor, carpet and wiring as well.

20140801_181221_zpswvlzcngb.jpg

Few months later this happened, poor thing :/

20140617_230716_zpsz1t0o5ue.jpg

New turbo on and shit, still to be tuned properly.

Larger wastegate and headstuds, fix the flex fuel stuff, battery relocation and a continue to tidy the engine bay more. I bought another gtr shell as a project track car so i suspect this motor will go into that car.

  • 2 months later...

love the wheels, my head is slowly moving away from the meister/professor style of stepped lips and bolted centers (which i still hrrrng for) and really appreciating smooth spoked/ concave wheels.
and those are a nice classic.

  • 1 month later...
  • 1 month later...

So due for a little bit of an update. Drove this around for a day to tune it towards the end of march and found:

Alternator no longer works properly when it gets warm, resulting in low fuel pressure etc etc

Bovs are open at idle and dont seem to like holding pressure

Aparently i cant run any less that 23ish psi without pulling the gate out to replace spring (ran 14psi before no worries?)

Solved all these problems by removing the interior........ Well in my mind at least.

Plan is to run NSW time attack for a laugh, probably need to get some tyres sorted haha. So weekend just gone removed seats and vacuumed carpet, removed amplifier and unnessisary cabling in boot. Started to remove interior trims to fit harness bar and continue wire tidy. Still have to fix above mentioned problems before it gets tuned again but at least i have a course of action.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...