Jump to content
SAU Community

Recommended Posts

Ok sorry confused .

I just spoke to Ross himself and it sounds like what I need is basically what Paul has which is the sensor pulley and Hall sensor to suit , in my case , an RB25 . He said all the pulley offsets are std , slightly different PWR steer wise to RB26 , and the Hall sensor mount has to suit the sump pan being used ie RWD steel/4WD/4WD + adapter plate ie 4WD RB30 .

Sensor wheel tooth count . Using 36-2 means that with their electrical converter box you can run (I think) computers looking for the std systems CAS only signals .

I like the idea that you can make a sub loom that splices into the CAS wiring so you can run the crank trigger or just the std CAS output if you ever had to .

The thing I need to confirm is that a Vipec Skyline plug in computer can be made to run the engine either way and then I'm in .

I need Paul or Yavus to confirm this .

Cheers Adrian .

Edited by discopotato03
  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

That system uses the same honeywell 101 pickup. Havnt designed a substitute for the cas on twin cam rb's yet. They just use the autronic disc in the standard housing. Works very well, and i can tell you, its very well priced

  • 1 month later...

ATI just announced this if it helps anyone contemplating a trigger

ATI Performance Products is proud to introduce four new Super Damper shell and complete damper
combinations with integrated steel trigger options that are compatible with the
new AEM Infinity and other stand alone engine management systems. These fully
CNC-machined trigger shells will be available on 6-inch and 7-inch Super
Dampers with a 6-rib serpentine option for both. The integrated 24-tooth
reluctor wheel eliminates the need for separate trigger wheels that can come
loose, and offers more accurate readings. These shells can be ordered installed
on a new damper or retrofitted on your current ATI Super Damper.

  • 4 years later...

I'm attempting an aem 24+1 trigger disc swap on my cas and it isn't going well. My cas is all pins and pressed bearings. Nothing like the bolt versions of the vg series cas. I have been reading and it appears as long as you can rig up some way of getting a signal to a sensor for cam or crank angle and duration you can make the rb ignition work. I've read that cam sensor setup on rb is unreliable, but was wondering if the jeep 4.0 flywheel crank sensor setup wouldn't be a sufficient setup. Why and why Not? It runs off of a flattened tooth on the flywheel. (Grinder and a drill) would be able to flatten a tooth for tdc and the sensor would be tapped into the back of the black to read the flywheel correct? Just a thought since this setup is very cheap and easy to come by. Any thoughts?

After constant issues with my CAS over 6500rpm during tuning and road tests I decided to bite the bullet and order the ross kit for my balancer.. Tuner was much happier and the car revs clean to 8000rpm now without coughing and spluttering.. I'm running the 12 tooth chopper wheel on the balancer with the billet CAS bracket and 1 tooth pickup on the cam with gt101 sensors, very happy with the look of the kit and the difference it made.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...