Jump to content
SAU Community

Recommended Posts

To do it properly you'll need to remove the whole roof lining from the car (not just the soft lining, the whole thing), You can do it in the car but may not be as succesful as it keeps trying to droop down while you're trying to stick it back up.

Peel back the section that is coming loose (if you just want to fix that section), spray with contact adhesive (from Bunnings, Supercheap, etc) on BOTH the soft roof lining and the backing panel (not too much that it soaks through), leave until it's tacky both sides then pull the soft lining back over where it needs to go (holding it up over the top, not letting it touch yet) then progressively press the two sections together working towards the outside. It's hard to explain so hopefully that makes sense!

To do it properly you'll need to remove the whole roof lining from the car (not just the soft lining, the whole thing), You can do it in the car but may not be as succesful as it keeps trying to droop down while you're trying to stick it back up.

Peel back the section that is coming loose (if you just want to fix that section), spray with contact adhesive (from Bunnings, Supercheap, etc) on BOTH the soft roof lining and the backing panel (not too much that it soaks through), leave until it's tacky both sides then pull the soft lining back over where it needs to go (holding it up over the top, not letting it touch yet) then progressively press the two sections together working towards the outside. It's hard to explain so hopefully that makes sense!

Dont use contact adhesive it soaks thru and gets clumpy , smells like hell for a while

Use Whorth headliner spray glue from autopaint shop , most others fail in the heat , or 3m super trim adheasive #90

Spotlight sells microfiber suede recover it , much nicer in black suede

To remove lay the seats down and roll down the windows to have room to slide it out easy

Its fragile so becareful

And remove the saggy cloth it you recover it so its smoothe or glue it down first

Edited by Carbon 34

mine is doing this a little too...but its not the liner peeling off the backing. its the whole backing falling off the roof, just replace the old double sided tape that used to hold it up there.

double check that yours isnt the same before you go buying expensive spray glues etc.

mine is doing this a little too...but its not the liner peeling off the backing. its the whole backing falling off the roof, just replace the old double sided tape that used to hold it up there.

double check that yours isnt the same before you go buying expensive spray glues etc.

pretty sure mines like that, i was gonna double sided tape it jsut havent been bothered... might do it befreo it gets worse though

mine is doing this a little too...but its not the liner peeling off the backing. its the whole backing falling off the roof, just replace the old double sided tape that used to hold it up there.

double check that yours isnt the same before you go buying expensive spray glues etc.

Mines doing the exact same thing, any recommendations on double sided tape to use? 3M I assume.

I remember being impressed by 3M as a company after studying a case study about them in uni, so personally I trust them as a company to provide quality products and would choose them among others. Very good R&D

sorry mate not mean to be rude/highjack your topic,where i can buy double sided tape and what brand? mine peeling off too...thanks guys.

Bunnings sells cheap white stuff

Autopaint store sells the 3m green semi strong removable

Or red backed non removable without force or remover soaked rag

Red is what car emblems and side trim is held on with

  • 1 month later...

Most auto stores should sell a spray adhesive for roof linings. Our go to your local hardware shop and buy a can of spray contact adhesive. Will cost less than $20 (i bought some today for a different use). Generally though you will need a new roof lining, because it is the foam becoming brittle that is causing the lining to sag.

Sorry, should have been more specific. The lining is fine, the drooping is where the headliner board (ie the mdf or whatever it is) attaches to the metal roof of the car. There are 3 or 4 contact points at the rear windscreen for this. I need to take another look, but I'm guessing there are Velcro pads or similar that are no longer glued on. New Velcro on loctite 401 could do the trick, spray adhesive sounds more like for the fabric. Just thought there may be a specific hi-temp rated interior glue.

  • 10 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...