Jump to content
SAU Community

Recommended Posts

On a serious note, is anyone in Melbourne that could lend me two 4 stud wheels 15, 16 or 17 inch that I could use to take photos for a roadworthy tomorrow? $$$

On an even more serious note, do you even lift, Brah? One does not simply alternate between epic trolling and srs bsnss.

Since when was 2/1 a fraction :/

since the invention of fractions.

you can still put whole numbers into fractions.

they're just not the simplest roots.

eg: 40/160 same as 20/80 same as 4/16 same as 1/4

all fractions.

all the same value.

This has been a good read, I'm going to put a inter-cooler on my NA falcon now :yes:

Tube & fin or bar & plate?

Far out, some people don't read...

I never said CHANGE the throttle body. I said put one (an extra one) on the intercooler pipe work before the throttle body on the intake manifold.

The throttle body on the pipe work isn't attached to a cable. It just works off its own spring pressure. Once the intercooler fills up, the throttle body will be forced to open and then the air that enters the intake manifold is pressurised to a certain degree (roughly 6 psi depending on how strong the spring is on the throttle body).

The same result can be achieved with a valve but it's more effort. The throttle body has a large diameter and the butterfly opens and shuts by itself with the amount of air running past it. It's a very simple method. It also allows the car to idle because it doesn't shut completely.

It won't run QUITE as fast as a turboed car running 6 PSI, but it's a damn good increase for a little amount of work.

Gutting your AFM definitely increases your power a little bit, as there is less of a restriction to slow the air down.

You can run a little bit rich but that doesn't matter because you're forcing extra air into the engine. Don't gut the AFM unless you're fitting an intercooler and a means of controlling the air flow (valve or throttle body).

Just try it. If you don't like the results you can remove the parts and save them until you turbo the car, you're gunna need the parts anyway.

I once had an XE Falcon with a drag plate air flow meter. Just sayin, but the boys at Ford were onto all this sh!t years ago.

Tube & fin or bar & plate?

I once had an XE Falcon with a drag plate air flow meter. Just sayin, but the boys at Ford were onto all this sh!t years ago.

If you use bar and plate, don't for get to mount it vertically (pod topside), otherwise the air will fall out.

Am I doin it rite? Bigger pod = bigger boosts f*kn whoosh?

Glad someone had the balls to reap the benefits of my advice. I bet your car is a completely different animal now, amiright?

Good job mate.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
    • After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
×
×
  • Create New...