Jump to content
SAU Community

Recommended Posts

Looking at fitting harnesses in my stag as when cornering at speed you have to brace yourself a bit at the moment. Anyone else fitted harnesses? Wanting to keep it practical with useable back seats so was thinking either a double release harness. Original plan was to put a harness mounting bar behind the front seats but not found any for stageas.

Link to comment
https://www.sau.com.au/forums/topic/419782-racing-harnesses/
Share on other sites

Yep I fitted a couple of Recaros from a Euro Honda or something - more comfortable than a race seat for my daily driver but heaps more control on the track. In this country (don't know about UK) if you fit a harness you have to be a member of a car club, run a log book etc.

Yeah reclining are ok. It's to do with cutting people out of cars. Harnesses have to have a red release button so can easily by identified and seats must recline so they can get you out on a spinal board. It's meant to come into affect in April, they tried about a year ago but realized none of the mot garages were prepared.

Yeah reclining are ok. It's to do with cutting people out of cars. Harnesses have to have a red release button so can easily by identified and seats must recline so they can get you out on a spinal board. It's meant to come into affect in April, they tried about a year ago but realized none of the mot garages were prepared.

As much as it pains me; that's actually a very smart policy.

At least there's logical reasoning at play in the decision making process; rather than the usual "Don't do it or we'll fine you" mentality we have in Australia...

Providing you have a WC34 Stagea a relativly cheap and good looking option is a pair of front seats out of a R32/R33/R34 GT-R. I believe they bolt straight up!

Personally I wouldn't be using a harness on the street anyway. While you are strapped in you can't move your body to look around properly (ie checking blind spots while merging lanes and parking)

  • 1 year later...

Honestly I found I could corner much faster while held in with a decent seat - I have used an aftermarket bucket seat and also a Recaro from a Euro Honda and both gave excellent results. I suspect a GTR seat would be also be ok and would have the advantage of bolting straight in to the existing holes without the need for an aftermarket seat base and slider.. As part of my cert process I had to fit seat belt anchors to the transmission tunnel so pretty secure as well.

You do realize that the back seats have to be removed and the belts must go back as straight as possible so as when you go over you body weight doesn`t go on your shoulders >back , Cams stipulation read the regs also road authority.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...