Jump to content
SAU Community

Recommended Posts

Hi,

Just about to flush the old fluid in my 33 GTST. Want some suggestions for a decent quality brake fluid thats; A: readily available B: not stupidly expensive.

Car is being built for weekend circuit stuff and occasional drift days.

cheers

I get away with Nulon Xtreme (280 degrees) - not as good as Motul (315 degrees), but a lot cheaper and easy to find. Last time i bought the Motul is was $25/500ml, Nulon was $11/500ml.

I get away with Nulon Xtreme (280 degrees) - not as good as Motul (315 degrees), but a lot cheaper and easy to find. Last time i bought the Motul is was $25/500ml, Nulon was $11/500ml.

I use this too, so far I have used it on mountain roads, drifting and 'fun' track days, never let me down at all. It comes on sale sometimes for $8 too.

I have been using the motul dot 5 up in darwin. im now going to the bendix super dot 4 which is $8/500ml compared with $30/500ml for motul. My reason for the swap motul is a lot harder to get now with the closure of autobarhn.

  • 6 months later...

In New Zealand Toyota dealers have started selling Motul products under the TRD (Toyota Racing Development) brand. I got Motul RBF600 brake fluid for about $20. It is genuine Motul - the label says TRD Sport Brake Fluid by Motul and says made in France by Motul and distributed by TRD Asia so maybe you could check out your local Toyota Dealer. They also sell the Motul racing synthetic oils.

  • 3 weeks later...
  • 1 year later...

Not a bad thread. I was using the Xtreme dot 4 fluid, albeit too old, and it boiled and failed completely on my last track day. The car is an HR31 GTS coupe with standard brake master cyl and booster with R33 gtst front brakes (RB74 pads and DBA 4000 slotted discs). I dont remember the old fluid costing too much but what is a next step up from that? I don't really understand the dot rating, master cyl says to use dot 3, is that just as a minimum?

Run 'Super DOT 4', don't bother looking at DOT 3.

Besides Ripco, it seems other stores aren't stocking Penrite Racing brake fluid any more :( (unless you buy online). You can get Nulon equivalent from Supercheap/etc though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...