Jump to content
SAU Community

Recommended Posts

When i first purchased my r33 in November of 2010 it was in a somewhat sad state of affairs, faded (and in parts peeling) gunmetal paint covered the majority of its vulnerable body.

The car itself was a 93 E-Ecr33 (that's right folks she's a type S :P) and like all type S cars was powered by the non turbo variant of the rb25 and backed by the odd 5 speed auto jatco box. So in short it wasn't exactly a speed demon.

It looked something like this when i picked it up (don't let the polish fool you the paint was bad): ITF6lf7.jpg

It wasn't long before i got sick of looking at the horrible flaking off paint and tool the car down to Steve at wrapture stylings and got him to wrap the top half of the car in black (god those rims are bad)

zcgsAMH.jpg

After getting sick of being teased left right and centre by practically everyone for the dinner plate chromies (18x7 +43 :/ ) I sourced a set of rims off boost cruising and a week later they were on the car (they look like Veilside Andrews, but are probley fake, I have no idea). Somewhere along the line I picked up a series 2 boot as well.

A few months past and after over 220k and multiple trips past that 7k mark on the tacho the poor little rb screamed no more and decided to spin one of the big end bearings, the car remained stationary for over six months while trying to source an engine and after eventually finding one was transplanted into the car over a couple weekends (with more beer consumed then I'd like to think health and safety would approve of). *note nismo sticker for more killerwasps

0vaw2hg.jpg

Using the forces of sheer luck the motor started and ran like a dream, this was followed shortly after with another trip down to Wrapture for a full body wrap in chilli red vinyl:

aCiUCqc.jpg
BsHSQAF.jpg
vHKJxv9.jpg

Which brings us to September 2012, when after a trip home from power cruise resulted in a very blown up auto and me stuck in 3rd gear limping home, by this stage you can imagine my frustration with this car. But, this broken gearbox became the catalyst that would eventually result in "The Abomination" (as dubbed by SAU Qld) being built.

Within weeks I had decided I was through breaking Nissan products and thought I'd start trying to break a few bits of GM gear instead. So it was off to eBay where I sourced a vz ls1 (which proved more costly then first imagined) and a 4l60e auto gearbox to be transplanted into my unsuspecting r33:

XDJh6CG.jpg

*part two coming soon

Link to comment
https://www.sau.com.au/forums/topic/422076-the-abomination-wtf033/
Share on other sites

Obviously step one was getting all the old Nissan stuff out and test fit up what the GM motor looked like in the nissan bay which ended up with the car looking something likeeeee this:

OAZz6nZ.jpg

From there engine mounts were fabbed up and the trans tunnel lightly massaged to accommodate the 4Ls larger bell housing:

PAuQFgw.jpg

m76HBVZ.jpg

Not long after the radiator was fitted and the gearbox crossmember fabricated under the car, at this stage a 3inch single piece tail shaft was ordered and turned up within a few weeks:

qHiXEEt.jpg

sm2gbjK.jpg

Aparently I have no photos of the tail shaft but it looks like a tail shaft lol.

We ran into issues with the fly by wire throttle body and eventually decided to convert it back to a cable throttle from a vt which intern ment a swap over to a vt ecu, we had this sent off to vengeance performance for what is basically a bandaid mail order tune until enough cash is there for a head and cam swap (and a decent tune) but for what it is it goes well ;)

A few weeks later the extractors were fabbed up as well as the rest of the system which consists of the headers into a y merge and then into a mandrel 3" system with a single four inch resonator and a 3" in twin 2 1/2 inch out rear muffler.

Eun4hO9.jpg

As the gear box has been manualised a B&M pro ratchet shifter was purchased and installed into the existing r33 centre console, again more "massaging" of the factory stuff and it fitted up without two many complaints ;)

mUiok1r.jpg

I know I've kinda crammed this all into a pretty short process but the general idea is there, the wiring was done by home grown kustoms in Toowoomba and as the car sits now is all mod plated up and ready to attack the mean streets of Toowoomba (as soon as I'm off these damn p plates)

Future plans:

*built 4l60e/th400

*Porter heads

*Largish cam (something in the 23X range) + required accessories

*obviously a retune

*3200 stall

*racepak dash

*New coil overs as the current ones are stuffed

... The list is really endless, ill keep this thread up to date with how the car progresses :)

T2UAS1N.jpg

It's kinda hard to get a video as I can't "legally" drive it, I'll try and get some up soon.

But it definitely does go :)

Find a private road/property like i always do :)

They were hecticly bad, literally got laughed at by SAU people lol

And this is something new? :P

There is but only one criticism I have of your setup, and no, it's not the fact it's auto...

The radiator support, if your gearbox and motor setup was anything like mine, it means you're going to have to do the old split the gearbox and motor apart while in the car if you need to pull the motor out again... It's my only issue, I personally would have made that rail a bolt in piece...

And in saying that, it makes me want to finish mine off really badly :(

i can see why! can i take it for a spin next month when im up? :P

dont like the wing much either but thats my opinion! overall tho nicky boy coming along nicely :)

Yer I get a lot of hate on for the series 2 wing? No idea why, I still have to series one wing sitting around in the shed lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...