Jump to content
SAU Community

Recommended Posts

Hello,

this is my rb26/30 build

by kanaris engine in melb

rb30 block - cryogenic block and girdle

cp pistons

9310 pins

upgraded loxx by cp

carrillos rods

AT1 balancer

L19 Head studs

Jun 12 main studs

9L sump ASR

Billet motorsports external oil pump kit

annual groove main tunnel

Head getting done now

2mm inlet/2mm ex valves

supertech valve springs seats retainers

ferrea valve locks

tomie 260/270 cams 10.25 lift

tomei lifters

tomie cam gears

looking at 1000hp at the engine

going in vl

post-87775-0-67934300-1366281902_thumb.jpg

post-87775-0-07005600-1366281915_thumb.jpg

post-87775-0-07661800-1366281926_thumb.jpg

post-87775-0-42773000-1366281938_thumb.jpg

post-87775-0-10906700-1366281950_thumb.jpg

post-87775-0-54303800-1366281964_thumb.jpg

post-87775-0-53420400-1366281976_thumb.jpg

post-87775-0-68541000-1366281985_thumb.jpg

post-87775-0-61220500-1366281996_thumb.jpg

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/423779-rb-2630-build/
Share on other sites

I always thought running flat tops means u can run more lift.

comp ratio going to be around 7.8 to 8.1

reason that low comp - less pinging high boost ,

makes more power then high comp - all types of fuel

I notice a lot of high comp boost rb have head/studs lifting issues

allways prefer low comp high boost/ high comp low boost

Link to comment
https://www.sau.com.au/forums/topic/423779-rb-2630-build/#findComment-6823429
Share on other sites

  • 1 month later...
  • 3 weeks later...

I here'd about weathering/seasoned blocks are better for hp than new block for cast iron - new block will move and flex up until 100,000km

Idea is the hot and cold temp stop the cast iron from expanding/ flexing - taxi blocks would be good idea

I left the rb30 block outs side for 6 months bare wit the girdle and just befor sent to engine shop I went to cryogenics

I believe this theory works , some might disagree

crank wouldn't think be any benefits

only cost $200 shop in melb -http://www.cryocycle.com.au/

Gerry

Edited by chairman
Link to comment
https://www.sau.com.au/forums/topic/423779-rb-2630-build/#findComment-6922218
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
×
×
  • Create New...