Jump to content
SAU Community

Recommended Posts

I set mine up yesterday, seems I missed setting it up correctly, when the card got full it just stopped recording.

Downloading the software now to see what the vids are like after I played with some settings to see if I can get auto deletion going.

will be interested in a 2nd group buy.

so, any night vid?

or track vid?

or track at night?

i have night vids tho yet to up them, there are a few settings all seem to change the quality/outlook

Edited by Frosty

I set mine up yesterday, seems I missed setting it up correctly, when the card got full it just stopped recording.

Downloading the software now to see what the vids are like after I played with some settings to see if I can get auto deletion going.

default setting is every 10mins a new file is written. Check in the software or look at the contents of card you will find files

Quality looks sweet. I'll be keen for the next group buy.

Did see a $60 special at jb's for a small similar unit. Have to see if it stacks up

Found it

http://www.jbhifionline.com.au/car-sound/car-accessories/uniden-vehicle-accident-camera-with-night-vision/684868

Can someone advise the benefits of the group buy unit over this? Keen ez

Edited by barraspalding

Read the review left on that link. Think that explains why this one is better :yes:

"Now the BAD: optics! The most important feature of any camera - quality of video recording. Picture is rich with colors, but sharpness is very low. Almost like out of focus. You can see the number plates only when right behind at the traffic lights. Up to 720p it is bearable with refresh rate (no specs on this) yet jerky with some fast movements around (turning). Above 720p is too jerky (too low refresh rate "

"Now the BAD: optics! The most important feature of any camera - quality of video recording. Picture is rich with colors, but sharpness is very low. Almost like out of focus. You can see the number plates only when right behind at the traffic lights. Up to 720p it is bearable with refresh rate (no specs on this) yet jerky with some fast movements around (turning). Above 720p is too jerky (too low refresh rate "

EDITED coz im a twit....hahaha

Edited by Frosty

Quality looks sweet. I'll be keen for the next group buy.

Did see a $60 special at jb's for a small similar unit. Have to see if it stacks up

Found it

http://www.jbhifionline.com.au/car-sound/car-accessories/uniden-vehicle-accident-camera-with-night-vision/684868

Can someone advise the benefits of the group buy unit over this? Keen ez

sinista has covered it from the reviews on JB

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...