Jump to content
SAU Community

Getting The Best Out Of A Mechanics Service

Haxorz

By Haxorz,
in General Maintenance

 Share

Recommended Posts

Haxorz Rising Star

Haxorz

Posted
Posted

Hey guys, I'm wondering how everybody gets the best out of a mechanics service, because basically I'm hesitant to get anyone do a good job.

I've tried a few different mechanics, and have even given them the log book and specifically asked to service it as per the book 'yeah sure no worries'.

The book stated it required air filters and the in cabin micro filter.

I get the car back to find out that they just blew out the air filters and pretty much ignored all the other stuff. Getting things like wipers done is a 'special request' where they have to order in the special blades and charge appropirately! I understand the in cabin micro filter is a rare thing, but the air filters! Come on!

Sure I can do the reaearch, find all the part numbers, call them up and book it in weeks in advance so they have the parts on hand (and overcharge me for!) and then specifically state all the things that need doing, but what a pain! I'm paying $400+ here, I shouldn't have to do any of this IMO.

Also oil - they charge $99 for 5L which I can buy from Big W for $50 (I know this is to mask higher labour costs). I'm not sure if I should supply this myself or if it will piss them off.

My car has a rough idle and I'm guessing could use a throttle body clean out, although I'm just read how important it is not to disconnect the sensor otherwise it'll screw things up - do I need to specify all this to them as well? I'm a little hesitant getting others to do this also.

My running costs are tax deductable and I don't have garage space so servicing at home is not an option (certainly not for jacking a car up and changning the oil).

I have previously taken my car to two well known Skyline performance guys here and I wasn't impressed either, little things like fuel filters and washer bottle top ups just don't get done again unless specified.

Any tips on how to get a good service? Would a Nissan dealer be better? Any suggestions for inner Melbourne shops?

Plattsy Grand Master

Plattsy

Posted
Posted

Hey guys, I'm wondering how everybody gets the best out of a mechanics service, because basically I'm hesitant to get anyone do a good job.

I've tried a few different mechanics, and have even given them the log book and specifically asked to service it as per the book 'yeah sure no worries'.

The book stated it required air filters and the in cabin micro filter.

I get the car back to find out that they just blew out the air filters and pretty much ignored all the other stuff. Getting things like wipers done is a 'special request' where they have to order in the special blades and charge appropirately! I understand the in cabin micro filter is a rare thing, but the air filters! Come on!

Sure I can do the reaearch, find all the part numbers, call them up and book it in weeks in advance so they have the parts on hand (and overcharge me for!) and then specifically state all the things that need doing, but what a pain! I'm paying $400+ here, I shouldn't have to do any of this IMO.

Also oil - they charge $99 for 5L which I can buy from Big W for $50 (I know this is to mask higher labour costs). I'm not sure if I should supply this myself or if it will piss them off.

My car has a rough idle and I'm guessing could use a throttle body clean out, although I'm just read how important it is not to disconnect the sensor otherwise it'll screw things up - do I need to specify all this to them as well? I'm a little hesitant getting others to do this also.

My running costs are tax deductable and I don't have garage space so servicing at home is not an option (certainly not for jacking a car up and changning the oil).

I have previously taken my car to two well known Skyline performance guys here and I wasn't impressed either, little things like fuel filters and washer bottle top ups just don't get done again unless specified.

Any tips on how to get a good service? Would a Nissan dealer be better? Any suggestions for inner Melbourne shops?

i took my 33 to dandenong nissan, they dfo a mega job. even washing and polishing the car. looks like its a bit of travel for you but hit em up if your willing. they will follow the book to the letter.

ZRBE Experienced

ZRBE

Posted
Posted

I'm in the same predicament.. I don't trust mechanics anymore, won't name any..

There are 4 that I will not go to again. Also this was not in a skyline or import, these were only a 93 festiva and an 83 corolla..

I'll start with the rolla, took it in just after buying the car for new spark plugs, full service. Gearbox/diff/engine.. Told them to also look at my brakes at the front (a little warped)

Got the car back and it was fine.

Next morning driving to work and hear a loud clunking noise coming from Left front wheel..

I live 400m from this mechanics workshop, so I slowly hobbled there after leavin my house, as I pulled up they were just opening and was watching me slowly coming down the road (he knew something didn't sound right) told me to drive into there garage, as I did my front wheel FELL OFF! And scraped along the ground a good 3m.. I told them someone must have not tightend up the nuts for my wheel.. Long story short.. I'm the one full of crap, they blamed ME for the wheel falling off..

Festiva is a whole other story at a different workshop...

Now I do not trust anywhere to take my skyline when I take her in for a service etc.

Haxorz Rising Star

Haxorz

Posted
  • Author
Posted

i took my 33 to dandenong nissan, they dfo a mega job. even washing and polishing the car. looks like its a bit of travel for you but hit em up if your willing. they will follow the book to the letter.

Thanks for the tip #@Plattsy. How much does your average service cost down there and how long does it take?

I know FTG Nissan are one of the two 'premium' Nissan dealers in the state (only ones that sell/service GTRs) and were really good for the little I've had to do with them (getting a spare key reprogrammed).

Being a V36 I should also look at Infiniti dealers I suppose.

Plattsy Grand Master

Plattsy

Posted
Posted

Thanks for the tip #@Plattsy. How much does your average service cost down there and how long does it take?

I know FTG Nissan are one of the two 'premium' Nissan dealers in the state (only ones that sell/service GTRs) and were really good for the little I've had to do with them (getting a spare key reprogrammed).

Being a V36 I should also look at Infiniti dealers I suppose.

i could not tell you mate as i get fleet rates plus another discount. they have serviced my wifes kia twice and did the 100k service on the 33. they charged 200 for that but i supplied all the parts. timing belt, bearings, water pump etc.

Haxorz Rising Star

Haxorz

Posted
  • Author
Posted

i could not tell you mate as i get fleet rates plus another discount. they have serviced my wifes kia twice and did the 100k service on the 33. they charged 200 for that but i supplied all the parts. timing belt, bearings, water pump etc.

And they are happy having you supply parts or were they a little miffed at it?

That to me seems like the way to go.

Plattsy Grand Master

Plattsy

Posted
Posted

And they are happy having you supply parts or were they a little miffed at it?

That to me seems like the way to go.

they where very happy mate! speak to the service manager there. his name his glen. explain that a guy you spoke to on a forum told you about the work they did on his 33. mention my name (paul) should be happy to help!

Plattsy Grand Master

Plattsy

Posted
Posted

and he also asaid his maintainence is paid for. f**k it. if someone paid for my cars to be serviced i wouldnt do them myself either.

scotty. how many jacks to build me extractors! haha.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

I would only fabricate turbo manifolds for you, extractors are for teh gays. :P

Claiming tax for servicing doesn't 'pay you back' you are still wasting cash hand over fist for what is literally a 5 minute job in the case of dropping oil in the VQ's.

Plattsy Grand Master

Plattsy

Posted
Posted

I would only fabricate turbo manifolds for you, extractors are for teh gays. :P

Claiming tax for servicing doesn't 'pay you back' you are still wasting cash hand over fist for what is literally a 5 minute job in the case of dropping oil in the VQ's.

i wouldnt tt the ls1.

but if i table build an ls6..... mwahahahaha!

ZRBE Experienced

ZRBE

Posted
Posted

Oil filter, oil and air filter changes are so easy to do on 95% of cars the thought of me paying someone to do it wouldn't even enter my head.

Do it yourself!

I'm fine at oil filter, replacing oil, changing wheels, air filter etc.

Everything else.. I'm screwed and wouldn't attempt doing something I have no idea about..

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted (edited)

I'm fine at oil filter, replacing oil, changing wheels, air filter etc.

Everything else.. I'm screwed and wouldn't attempt doing something I have no idea about..

There is only one way to learn ;)

Well that's not true at all but i do suggest at least having a go at doing servicings and stuff like that, its simple and really is a life skill worth having.

Edited by iruvyouskyrine

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...