Jump to content
SAU Community

Recommended Posts

Hip flexors I don't find too bad as in you can give them a good stretch and they come good, the back I'd be cautious of.

Yeah I'm not sure why my left side is so sore. I assume my technique is still off as I can see I'm rounding my back. I'm going to practise with a rod tonight and make sure it's staying in contact with my head, back and tailbone as I'm pretending to deadlift. Hopefully I can fix the problem.

I'd concur with that, I used to try and use the window and it made me over extend. My session with Matt helped me get the feel for where it should be and how it will feel when the lower back is straight (the upper back can be rounded and lower back still straight, if everything is straight it puts excess stress on the lower back via leverage).

pfft. mirrors.

If this is deadlifts or squats then mirrors shouldn't be used. Looking at them while moving is contrary to what good form looks like for both.

L33SH, you should be ok without checking the back. Deads do work the lower back so occasional soreness is normal. Just check the back mobility for issues.

Edited by rev210

22/07/13

Flat Bench

25kg x 10

30kg x 10

35kg x 10

40kg x 2

42.5kg x 2

45kg x 1

Squats

30kg x 10

35kg x 10

40kg x 10

45kg x 10

45kg x 7

50kg x 2

Close Grip Lat Pulldown

30kg x 10

40kg x 10

40kg x 10

50kg x 10

55kg x 8

60kg x 2

Incline Press

20kg x 10

20kg x 10

25kg x 9

25kg x 9

30kg x 3

30kg x 3

Tricep Pushdown (double pulley)

25kg x 10

30kg x 10

35kg x 10

35kg x 10

37.5kg x 8

40kg x 4

40kg x 3

Captains Chair Leg Raises

10

10

10

10

Captains Chair Knee Raises

30

You put your right foot in, you take your right foot out, you put your right foot in and you shake it all about (you don't have to do this part, Dan).

Captains chair is a static machine where you support yourself in the air by your arms, then raise your legs up in front of you. It's sort of the opposite of a situp. Works hip flexors and abs + bit of hamstring stretch in there too, depending how far you bring the legs up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...