Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Do still have these parts?

2door power window motor

ignition barrel plastic ring

indicator stalk or turn/bright switch

power window switch Left

quarter glass, with intact rubber molding

Don't suppose you'd happen to have a standard battery brace? the one that bolts to the rad support?

Hit me up on 0419170619 if you do. happy to pay postage.

  • 3 weeks later...

R32 parts for sale plus a few other bits

R33 rotors. Calipers.hand brake cables and drum assembly with knuckle $130-
Under dash panel driver side with fuse box cover $20
Stock r32 side mount intercooler $50
A pillar trims $30 each or $50 for a pair
GTST air con condenser $70
2 x r32 hand brake and cable $70 each
GTR front strut brace $100
1 x pairs of r32 5 stud front hubs and up rights $100 a pair
4x lower quarter trims $30 each
Rubber gear box surround with metal ring $20
2xglove boxes
Under dash trim panel $15
R32 glove box $30
3 x speedo clusters 2 x grey, 1 x blue dials $80 each
2 x climate control unit $70 each
Centre console dash panel radio surround $40
Upper rear trim driver side all clips still there cracked in corner otherwise good con $40
Rear bar $50
Rear reo $70
Tail lights no covers $40 each
Steering Colum surround $50
Rear parcel shelf $40
Centre console ash tray $10
Window black box driver $50
Front bonnet latch and support $50
2xwiper motors $40 each
RB20 speedo cable $70
Nissan din pocket $20
Washer bottles rad overflow and washer $40 each
Non projector headlights $200
1 x passenger window switch $50
Air con box $50
Heater box $50
Passenger window reg $70
Passenger and driver kick panel $20 each
Boost sender/sensor R32 $20
Clutch pedal $70
Break pedal $30
Carbon canister $20
Boot lid $70
Bonnet latch and cable $40
Fuel/boot cable $50
1 x stock r32 steering wheels ok condition $50
Surround ash tray $10
Front LCAs $120 a pair
Fuel pump $40
Dash all good vents small bubble on front $150
Door shells $100
2xcluster surrounds $20 with some cuts in them
Light switches/wiper switches $30 each
Carpet $100
Gear boot $10
Hand brake boot $10
Driver side dash vent $40
Sun visors $10 each
Rear view mirrors $20 each
Clutch master $30
Gear boot plastic surround $30
Indicators with wiring no outer covers $10
Wiper arms $10
Driver dash vent $40
Stereo brackets $20
2x driver side window switches $70 each
16” rays 2/3 piece $200 with good tires

  • 2 weeks later...

Are the clusters from a gtr? Chasing one for my rb s13 conversion. Prefer grey with the needle stop at 9 o'clock. Pm me or text 0419 856 391

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few suggestions: Do you have the option of retarding your exhaust cam gear to bring the power band over to the left? VCT would be turned off after you make peak torque, you see the power/torque will decay faster with it left on all the way to the limiter Once VCT is turned off, you'll find the motor will take a bit more timing being ramped in Send its mum, more boost! Of course, depends on your exhaust pressure.
    • Tow a boat... people won't know wtf is going on 🤣 
    • I was back on the dyno again yesterday after completely revamping my methanol injection system. I was making 440kw at 19psi. Great, this is more then I was making last summer with my old meth system at that pressure, and I figured it would be smooth sailing up to 30+psi. We continued increasing from there and by 25psi, I had only hit 455kw. Dyno sadly lost utility power at this point and I left. We seemed to be on course to hit the same power wall as last summer (477kw@27psi). This is a built RB25 S1 stroked to a 2.8. Built and ported head with Kelford 272/262 cams. Precision 6466 Turbo. Tuner last year believed the power wall is a mix of RPM limitations (Hydro lifters/Limit set at 7600RPM) and fueling. With my new meth system, we're seeing zero knock now but it still won't go up.  What else can I do at this point? Here's my train of thought.  - It's clear from the dyno graph that I would easily make power to 8500+RPM but I'm limited to 7600RPM. I could risk increasing my limiter, but hydro lifters have me worried. What are my options here besides going NEO head or solid lifter conversion? I'm rocking a 1.05AR turbine on my 6466. Would dropping down to a .84 help shift that power down in anyway? - We're only seeing roughly a 30kw difference at the top end with VCT on or off. Is this normal? I want to confirm VCT is working properly. - Should I look into other cam options?  - Should I just keep increasing boost and see if she wakes up later on? I would expect to hit 600rwkw around 35psi with my 6466.   
    • First thought is to use a ram mount (to hold the ipad) + windscreen suction mount. The arms on the ram mount can be as long as you like, should be able to position the ipad pretty well with that setup. 
×
×
  • Create New...