Jump to content
SAU Community

Recommended Posts

high all,, I got a gtr with the above turbos,

its forged internals and minor head work, still standed cams and valves,

power-fc tuned to 380hp at 15psi,

blead up with gfb bleed tap,

I will be going to a electric boost controller at some point but problem I have it I have nothing under 3500rpm, no real pull until 4000rpm when boost comes on,, I went with the dash 7's over the 5's due to lag, tho I think this turbos are lagy as hell, ??

if I fall off boost there is nearly no power at all, is this normal for the -7??

I no a EBC will help it get on boost sooner tho this seems like a lot of lag?

Link to comment
https://www.sau.com.au/forums/topic/429128-rb26-2860-7-slow-to-boost/
Share on other sites

has base timing been looked at? my new engine from japan was 10 degrees advanced and was VERY laggy.

put it back to 20deg BTDC and it's running perfect.

you'd think the Japs would know how to get it right but you'd be surprised.

The adjustable actuators with any more than about 2-3 turns worth of preload will give more than 17psi boost.

I found out this morning...I'm still yet to tinker with my profec b 2 but am confident that if I have standard preload on the -9 actuators

and adjust the start boost high enough, it will give me my 15psi that I want, nice and early. Which sounds like what you're trying to achieve.

You should have about 7psi by 3000 and 15psi by about 3900. You could try disconnecting the boost signal to the actuators and plugging the line then go for a CAREFUL run up to say 3500 or 4000 to see if the boost comes on any better. Dont go further than this as boost will keep climbing! If you notice boost building better, then an EBC should help.

-7s come with adjustable actuators standard so check the preload on the actuators - usually 1cm is a good start. Then apply some air pressure to them via the common feed line to make sure they open the same amount at the same time.

If one turbo is spooling and the other isn't you can get shenanigans like shuffling happening. It's basically the early turbo forcing the turbo that is dragging its heels into surge by increasing the downstream pressure above what it would be if the slack turbo was running by itself.

Edited by GTSBoy

also cam timing will increase off boost power and bring turbos on sooner

you say forged motor what is the comp ratio ?, base timing, as stated already, makes a big difference

check the actuators are set correctly and a EBC will also bring turbos on sooner by reducing waste gate creep

what exhaust do you have ?

is there a rag in your intercooler ?

hi all,, it is lowerd compresson but im not 100% sure to what, I haven't checked the cam timming tho will, maby a set of adjusterball cams?

timming was set at tune, if I remember im seen a max of about 43deg timming on boost? id have to check again,

iv tried to set the wastegate's tho the actuator adjusters seem to be pressed onto the threaded sharft? it still has a lock nut on the thread, no mater how hard I tried I couldnot turn the rods on the threads, they are genuan brand new garret turbos, exhurst is a hks 3.75" fullsystem , 3.75 high flow cat,

the rag, youv put the fear of god into me but im 100%% sure there is no rag I left in there :P

I once found a 13mm spanner in the BOV return pipe

Lowered comp ratio will make turbo spool later and make it feel sluggish off boost

A set of cam gears tuned for response will help to

hahahaa thats gold!

loosen up the nut and remove the circlip carefully at the end of the rod (magnet the circlip to stop it flying off), then adjust the rod

iv tried to set the wastegate's tho the actuator adjusters seem to be pressed onto the threaded sharft? it still has a lock nut on the thread, no mater how hard I tried I couldnot turn the rods on the threads, they are genuan brand new garret turbos, exhurst is a hks 3.75" fullsystem , 3.75 high flow cat,

loosen up the nut and remove the circlip carefully at the end of the rod (magnet the circlip to stop it flying off), then adjust the rod

did exactly this, still no bingo on eather turbo,

my 13mm is accounted for so its not that haha, I do think its the decomp motor that is it,, on my standed twins I wasent making fullboost till about 3500-4000 eather, so cams/cam gears it is,

  • 1 year later...

well this is old ;)

, come along way since then, engine is striped down, getting 87mm wiseco pistons as no6 piston took one for the team,

im going to pumping the boost into this set up, just wating for a spanking new crank to turn up then rebuilt time, ( had been ground to much in the past)

responce is my aim for this, i now have adjusterbull cam gears, still running the -7s( going to set 15psi gate press, then up with a eboost), what cam deg/lift would be a good combo for this?

looking to run around the 20-25psi range with flowing mods,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...