Jump to content
SAU Community

Recommended Posts

Purchased my r33 just under two weeks ago, all is good except recently i've noticed it's really difficult to put the car into 1st gear and reverse at times especially when the car is rolling (obviously i dont put it in reverse while rolling forward) i'm not sure if its always keen like this or if i've only just realised.

Link to comment
https://www.sau.com.au/forums/topic/430270-r33-gtst-clutchgearbox-problem/
Share on other sites

just the way they can be. as long as it goes in when stopped without any major resistance then all is fine.

def recommend to change the gearbox and diff oils for some new quality stuff as most skylines have this neglected and can really benefit from it, you'll probably get a far smoother shift and better longevity from your driveline.

#@34GeeTeeTee the pedal feels fine, engages about half way down. when i'm stationary it's easy to move into gear, it's only really when in motion that it seems to be a problem have to put a bit of force into putting it in first.

and this is a noob question but where do i check the clutch fluid level? do i have to bleed it before refilling it or anything?

#@34GeeTeeTee the pedal feels fine, engages about half way down. when i'm stationary it's easy to move into gear, it's only really when in motion that it seems to be a problem have to put a bit of force into putting it in first.

and this is a noob question but where do i check the clutch fluid level? do i have to bleed it before refilling it or anything?

In the engine bay you will see the little rezzy near the brake fluid... the brake fluid is a bright yellow cap and the clutch i think should be a black rubbery type cap! Just take it off being careful not to spill any fluid on paintwork and see what it looks like, you should actually be able to see the level without taking the cap off but i would check the condition anyway as its more than likely due for a full flush as most get neglected!

When are you trying to put it in first while in motion? Not something you need to do too often?

just getting a feel for the car really, it's the first manual i've actually owned so its kind of just a learning process for me at the moment

Fair enough! Well if you have any mates with them or know people that drive them get them to have a quick test drive and put your mind at ease!

It could be perfectly normal and you are worrying for no reason, you could have an issue.... Hard to tell from interstate lol

Let us know how you go with it and enjoy the car man!

  • 2 weeks later...

Its a manual!

how many manuals do you know that are easy to get into 1st n reverse when the car is moving?

iv owned 8 manuals and 6 you couldn't get 1st or reverse if the car was moving. Also 2 R33s, 1 you couldn't n 1 you just barely can. Its normal as long as it goes in without crunching when stationery. N yes, sometimes it can even be hard to find reverse.

Its a manual...

:)

Good grief. I have a gearbox that was so reluctant to shift when it was first installed that it wouldn't actually engage any gears at all until we drained the normal oil out and put shockproof in it. That gearbox still likes to snick and crunch a little bit going up or down into the middle gears. And that gearbox is perfectly able to be shifted into first with the car moving at quite decent forward speed.

Does no-one know how to rev match anymore?

The car wont go into reverse while rolling because there is no synchro on this gear. Its not something you should really ever be doing anyway wether your travelling in forward or reverse. If your on a hill, put it in reverse BEFORE starting to roll backwards.

as for 1st, as already quoted, It's not the easiest gear to get in, usually you have to be travelling at a lowish speed or rev match as GTSBoy said. Mine shifts into first alright at around 15-20km/h (not 100% sure what speed as its usually when pulling up to stop or slow to near stop)

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...