Jump to content
SAU Community

Recommended Posts

Well BOLLOCKS.

Went out and got the NGK/NTK OZA395-E2 part and i can 100% say the plugs DO NOT FIT. Now I have to go return it and I'm back to square one re: the right sensor for the S2 Stagea. :D

If the sensor is the same (anyone?) I might just have to crimp the wires with the exisiting plug. Both have 2 black and 1 white wire so looks easy enough. Apart from plug, can anyone tell me if OZA395-E2 is alright for RB25DET NEO engines?

EDIT: Well, swapped the plugs and replaced with said part, it fits. Crimping wasn't too bad, but I hope it doesn't matter which white wire was connected back!

Edited by webng
  • 1 month later...
cant be bothered reading all of the pages...changed o2 plug by NTK for R32 GTR, front pipe one is a straight fit, the rears have to be cut as plugs are different.

Will post up part numbers got mine for $75 each

Global Auto Spares Part # 351-0019

NTK Part# KBA 16693

Sensor Type 0TD2F-2B

Needs a 17mm Spanner

But f**k me can someone help me with the R33 GTR part number?

I assume I have R33 ones in my bitch because it needs a 19mm

R33 GTR sensor (front at least) is a Bosch A24-621 115 68290

Global Auto Spares Part Number 351-0187

Same sensor for the rear, only lead length and plug differs.

Needs a 22mm spanner

18mm Thread - 3 wire Oval plug on a short lead - Titania

http://members.pcug.org.au/~jdeakins/facts.html helped me find what I needed

Global Auto Spares on the coast imports them

Chris Jeffis

0755310055

[email protected]

Hope this helps some people

  • 1 month later...

Hi Guys,

We are currently offer the NTK oxygen sensors for the R32 GTS-t/GTS-4 & R33 GTS25-t for $77 + delivery. If anyone is interested simply click the link below for transaction instructions:

http://www.skylinesaustralia.com/forums/t135194.html

Regards,

Andrew Sullivan

Kudos Motorsports

  • 2 weeks later...

its dead if voltage isnt moving after warming up car (normally it starts 0.3v, then after about a minute will start climbing upwards, then by around 0.9v and 5 minutes later car should be at operating temp so it will start swinging back/forth between 0.1/0.9v when car under light load/cruising).

normally when they are dead they sit either 0v or around 0.3v and dont move.

  • 4 months later...

to test the o2 meter. swich to diagnostic mode 2 and you will see the engine check light go on and off if you rev and hold your engine at 1500 rpm.

something that will help s2 owners

http://www.skylinesaustralia.com/forums/Di...S2-t210274.html

Edited by xr8eater
  • 3 weeks later...

I don't mean to be a slacker, but I cbf reading through 26 pages to see if anyone has done this on their GTR.

What are the part number(s) for GTR's and regarding the extremely tight space, what's the best way to do it? (ie: tools, do it yourself?)

Thanks in advance.

FVO is right. 26 pages is not going to help anyone.

I've chopped 140 posts out tonight. I'll try and knock a few more later this week. Once we've whittled it down to something manageable, I'd really love a keen SAUer to cut and shut the remaining info into something useable we can put into a new thread.

Full credit will go to the guy or girl that does the editing. We'll need something with headings, either by car or by something like "Part Number, Fitting, Sellers" or something like that. I'll leave it with you.

But yes, FVO is right.

Thanks Cowie165, I thought I was gonna get hammered for not reading the thread. If it hasn't yet been done on a GTR I am more than happy to be the first to write up a GTR tutorial considering how bad my fuel consumption is.

What I need at the moment (if anyone knows) are the part numbers for the GTR. They may be the same as the GTS-T, but I wanna be sure. Other than that, I wanna make sure that if I volunteer to do a tutorial on my car for the GTR that someone else won't get in before me after I took the time to take pics and so forth.

Hey no problem. I've gone through the first couple of pages tonight: R32 GTR has two different sensors. They aren't compatible with the EL Falcon and are different to RB26 sensors in the R33 and R34. There might have been some part numbers but it was bit of a blur. I was pretty much deleting any post that didn't offer some meaningful info, and saw LOTS of part numbers thrown around. Perhaps check out the first few pages and see how you go.

btw, if you aren't sure about your O2 sensor, I highly recommend borrowing a consult cable from a mate or even going down to Mr Nissan. It is VERY easy to diagnose the fault with OBD.

Alternatively, there was a link on page 2 or 3 (?) that apparently shows you how to check it with a multimeter. I think you just need to connect to the signal wire, and on a hot sensor you should see voltage steadily bounce between 0.4 and 0.8V. Don't quote me on the voltages though as I haven't checked in a while. The info is in the RB20/25/26 engine workshop manual supplement.

Thanks for all the info.

I'll first try to check if the 02's are in fact faulty and do a little write-up on how to check them with a multimeter and what should be expected voltage wise. Then I'm gonna find out what part number they are and if they are compatible with any other vehicle.

Thanks again for the heads up, much appreciated.

I tried to get the info together a while back. I put it in http://members.pcug.org.au/~jdeakins/facts.html

It's obviously incomplete. Most of it came from an old copy of the FAST database someone had. I updated one or two entries after asking the local Nissan dealer for info from his up-to-date FAST database, but that's all the time he could spare. I talked to NTK in Melbourne and found them to be very helpful. Only thing is, I suspect they have the part numbers for the front and back sensors R32 GTR swapped. Either that, or someone in Japan swapped mine. From memory, NTK only have one of the two R32 GTR sensors available - but that was a year or so ago, the last time I checked.

Far out James, looks like we just found our O2 sensor reference page! Nice work there. Would you mind if we reproduced the info here as a sticky? To make sure your efforts are recognised, you could create the thread and I'll go sticky it?

Funnily enough, I don't remember deleting any of your posts last night because they all had good stuff in them! :D

I'm very happy to move the table to Skylines Australia. It could be good for forum membership too - if I leave the table as it is on my site I can advise those who find it using Google etc to join SAU for an updated table.

Before I went back to study I thought this site was looking at hosting some pages, and starting a wiki. I can't see any reference to them on the front page, so I guess they both fell through. Do you have any suggestions on the best way to pass the table over to SAU so that members can add to the table when they find information? If it's a stickied posting we could end up with 26 pages of comments to it because no-one can edit the table in the lead posting. Or am I misunderstanding sticky postings?

Ok we're now another 60 posts lighter.

For the final sticky, it looks like we'll need:

Part Numbers (James has pretty much covered this)

How to test your O2 sensor (with Consult or PFC)

How to change your O2 sensor

How to reset your ECU

Any other headings? We can prob leave crimping and wiring for howstuffworks.com

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...