Jump to content
SAU Community

Headlight Restore Kit

Lemonnuff31
 Share

Recommended Posts

Lemonnuff31 Enthusiast

Lemonnuff31

Posted
Posted

Hi all,

I am looking to get opinions on whether the Meguires lens restoration kit is any good or not? I have faded headlights, and i think it is all external and this kit seems like a good place to start.

Is this any good, or are there other products you would recommend?

Finally, is there anything else I need, i saw something about UV protector or some such?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/431036-headlight-restore-kit/
Share on other sites
Sequel Apprentice

Sequel

Posted
Posted

Hi Lemonnuff31, I had this same issue. My headlights were getting opaque with a slight yellow tinge. I didn't purchase a kit and opted for three of the lightest grit sandpapers to use in conjunction with plastX and a polish buff drill bit....think i saved 20 bucks or so doing it this way. It did the job nicely and i was happy with the result. I think with the plastics used on headlights these days the coloration and smokiness is bound to happen with exposure to UV and the elements. I don't think its a one off thing to restore headlights but a little job that needs doing maybe once every few years to keep them looking immaculate and clear. There is science behind different plastics and how they react with varying chemicals and when i cleaned mine i didn't get to finicky and just went with the most tried and tested approach. When i do mine again ill be using the Meguires Kit you mentioned.... It comes with the plasiX included in the kit.

(Locky) Community Regular

(Locky)

Posted
Posted

bought the decent kit from autobarn... looked immac for about 3 months then the UV sealant started to look patchy like it was flaking off and the yellow started to return... think next time I do it im just going to use a polishing pad drill bit and buff the f**k out of them as a plastic s13 grill that was yellow turned out amazing with the buff pad

sonicii Veteran

sonicii

Posted
Posted

I have tried one of the kits (RainX kit). And if I had to them again, I would just be buying several fine grades of sandpaper and looking for the sealant on it's own.

I found the polish that came with the kit was next to useless. After using the sanding pads and perservering with the supplied polish, I ended up using my rotary buffer with a foam pad and a fine cut paint cleaner which did an awesome job of cleaning up the headlights after sanding. Made them look brand new. I then just applied the sealant the came with the kit. PlastX with a rotary buffer would probably work well too.

That was about 6 months ago, I live in North Queensland and my car is parked in the sun all day, and it still looks great!

Howaitonaito Mentor

Howaitonaito

Posted
Posted

Meguires do make the UV sealant on its own. Only problem is they do not sell it in Aus....YET!

Invision do not make the sealant by itself. I did ring them and they said they plan to do a bigger bottle in the future amd sell the products individualy in the future aswell.

Will the invision pack you need to be sparing with the sealant. V35 headlights are exactly small.

Sunkist Grand Master

Sunkist

Posted
Posted

Lol the Meg's stuff is useless shit! Last about 3 months, and becomes worse than before a lot quicker. Their sealant is .... Okay(loosely used) but doesn't last very long.

I used the glassylite kit off eBay( $35) and it lasts about 10months to a year. Pics?

Check out this shit

1378207024.5649.iPicit.jpg

1378207071.3461.iPicit.jpg

1378207121.7993.iPicit.jpg

Don't have any before pics as I wasn't expecting THAT good of results. But it worked wonders.

  • Like 1
  • 3 weeks later...
GH05T Grand Master

GH05T

Posted
Posted

guys the resto kits all work great, toothpaste will work great....we need to find a good sealant which stops the degrading process and group buy.

must admit the kit i got from sprints, i think maguires, has still held up very well for months.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...