Jump to content
SAU Community

Recommended Posts

Hi, my r32 (rb20) has a high flowed r33 turbo, front mount and a 3.5 inch cat back the actuator in the high flow is at 14psi.

I want a turbo that fully boosts by 2500 - 3000 ish and pulls harder than the high flow if I got it nistuned and bought a 3 inch full exhaust plus smaller turbo would that do it? Help me please or should I sell it and buy something else?

Edited by Barrellboy
Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

the nistune will help you out no matter what you do with Turbo's

There's a series of supporting mods you haven't mentioned in your post. So I assume you only have what's mentioned.

Just buying a smaller Turbo won't help by itself.

When you say buy something else you talking a completely different car ?

Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/#findComment-7001734
Share on other sites

By something else I mean a different car probably a wrx

A mate took me for a drive in his sr20 180sx and it pulled much harder than my 32 and was coming on boost soo early like 2600ish.. he had pon cams, tune, fmic, 3 inch exh and injectors. Can I get that low response with a 20 mine comes on at 4200 ish and pulls no where near as hard as his 180

Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/#findComment-7001748
Share on other sites

usually if its just a run off the mill highflow it probably isn't specced up to be responsive.. personally im not much for bitsa turbos. Do you have any exhaust leaks? what condition is the motor? ie compression. Can you get your hands on a stocker rb25 turbo?

Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/#findComment-7001764
Share on other sites

I don't know the compression but it generally feels like it runs well and came from a good family who imported it and didnt drive it too hard ( I know this) no exhaust leaks either. I could buy a stocker 25 turbo off gum tree but that wouldn't get me close to the response of the sr20 would it? The sr20 also has the stocker t25 turbo...

Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/#findComment-7001778
Share on other sites

I think you'd need more cubes, RB30et would hammer.. just my opinion

http://www.skylinesaustralia.com/forums/topic/423299-sa-rb30et-engine-package-240kw-motor-hd-clutch-box-etc-2500ono/

Edited by AngryRB
Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/#findComment-7001792
Share on other sites

a tune helps infinitely. Particularly if you are willing to lean on it a bit and push the boost, esp with an electronic boost controller.

take it to Garage 101 for a nistune on the ecu and tune. I doubt you will be disappointed. Per4manz are also a damn good turbo shop so unless that turbo was highflowed for a different vehicle in mind from the technician (i.e. R33) you will be good to go hard on not much more budget...

P.S. to get a car that pulls hard and makes full boost under 3000rpm is pretty much a holy grail (unachievable essentially) and will take a very good condition motor with a very good turbo setup and associated mods ($$$).

In an RB20, yeah, pretty much impossible.

Edited by jjman
Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/#findComment-7002124
Share on other sites

Would even worry bout a wrx, they are not even worth comparing, its like oranges and apples.

To get decent response witb rb20, get a electronic boot controller, a aftermarket ecu, nistune is good value for money, and budget and get a tune, the tuner can bring the boost on abit earlier with the electronic boost controller so that can help, and with the turbo situation go look for a hks 2530, can make up to 230-240 kw, with excellent response, or a hypergear or a highfliwed r33 with the op6 rear housing. Ive been through the whole situation before so if i were you id be going the hks 2530

Link to comment
https://www.sau.com.au/forums/topic/431296-more-response/#findComment-7002295
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...