Jump to content
SAU Community

Compression Test

morto86

By morto86,
in General Maintenance

 Share

Recommended Posts

Missileman Veteran

Missileman

Posted
Posted (edited)

On a warmed engine with all sparkplugs removed, with accelerator fully depressed and a charge on the battery capable of cranking the motor at 300rpm.

RB20DE/T/26DETT

New = 170psi

Low Limit = 128psi

Max cylinder difference 14psi

...from engine workshop manual.

Edited by Missileman
Ben C34 Grand Master

Ben C34

Posted
Posted

I just got the reply 210. Cold. Does this mean the head has been shaved previously

No as the comp ratio doesnt effect the compression test. it just ensures the rings and valves are sealing as they should.
Ben C34 Grand Master

Ben C34

Posted
Posted

Def 200 all round with snap on gauge and warmed engine. With researsh this proves the comp ratio therefor is 10:1. As for the knob who said the comp is not relayed to the ratio. Actually write out the equation.

Settle down. explain to me how an engine when built has a certain compression test result, then when worn had a lesser compression test result? Did it's comp ratio drop? can you run more boost cos it has less comp ratio? NO. explain how comp ratio effects the comp test results please :)
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Settle down. explain to me how an engine when built has a certain compression test result, then when worn had a lesser compression test result? Did it's comp ratio drop? can you run more boost cos it has less comp ratio? NO. explain how comp ratio effects the comp test results please :)

Well personally I would have though it was obvious that the higher the compression ratio the higher the expected compression test result . The value of the compression test for measuring wear depends on knowing the original compression so as above if the stock factory figure was 170 psi then yes 130 psi indicates a lot of wear which can be confirmed with a leakdown test. My engine had 130 psi compression when built because of the choice of pistons (CR about 8:1) and leakdown test is within limits at 5%

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • niZmO_Man
      Borg Warner EFR Series Turbo's V 2.0

      By niZmO_Man · Posted

      Not that I know from experience, but in theory you'd want your gate spring to be as close to target pressure as possible, so you'd go with the higher gate spring?
    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      Before I commit to it as I already have the wastegate off the car, would you change it to the 9psi spring instead of the 12, or whack it back on now and try your suggestion?   Edit: Actually I might just swap the spring and see what the logs say after another few pulls, as we know it's still spiking without the Mac valve in the picture so I need more data without the Mac valve trying to combat the issue.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Sounds good Hmm suppose the main thing is, how much do you care about this car? The filler doesn't make for a very good water barrier lol. If there was a tiny little bit of rust forming now, that in 3 to 5 years time becomes obvious under the paint (starts to bubble up), would it bother you? 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I already have the ability to datalog the voltage... what I can't do is correlate it to what the gauge is showing when I'm looking at the data at a later date. Or something like this. Except getting the oil to 125C+ involves me going 200+kmh at the track so you can imagine this is a little tricky unless I do something like note what the voltage is when I am at the top of 5th gear so I have a point to reference on. Drove car today. O2 still reading richer because hopefully not a leak instead of massive restriction I've introduced. Car really doesn't sound like a LS. It's quite strange. Pulled a bit of fuel out up top. This does potentially explain why my spark plugs looked like the car was running pretty over-rich. If I was tuning it to a ~12.7 which in reality was far richer than that in the past. It will be handy to have the dyno WB to compare my WB to to compare notes that's for sure. At this point I'm happy to just sit in the passenger seat and tune the thing given I've got about 7 million hours on the platform lol.
    • Chocolate Cheesecake.
      Infiniti Q60 Navigation Update

      By Chocolate Cheesecake. · Posted

      Yeah I understand you have to pay for an updated map or subscription service or something. But I can't even find a current map for Australia. My map is dated 2017, but didn't this car version still sell in Australia until 2021?   Also, just as an aside, the navigation system warns you of traffic incidences ahead.....why would they include that on a map they knew is not receiving live information. I am forever going to be warned of an incident that probably existed for 30 minutes 8 years ago.
×
×
  • Create New...