Jump to content
SAU Community

Recommended Posts

^^ been told the water line doesnt quite line up when swapping the turbos over?

Hrms, don't recall having that issue back in RB20DET boat anchor days.. I'm sure all I did was remove the stock RB20 hair dryer and just bolted up the RB25 heat gun.

  • Like 1

As for the water line, i ended up loosening the turbo off the manifold studs to jiggle the turbo to get them in, from memory.

This is helpful for anyone fitting a stock turbo its easier to do when the turbo isn't tightened up against the manifold.

Spray the nuts and bolts with a penetrating lube like penetr8 or penetrene or something first to save heaps of hassle.

Should be doing this before pulling old nuts and bolts off anyway. If you break something its not likely you can fix it on your own.

Good luck you should be fine with the swap.

What is the condition of the RB25 turbo you are fitting? remember these are very old hardware now

What is the condition of the RB25 turbo you are fitting? remember these are very old hardware now

Its a 45v4 turbo. The guy said it was from a R33 and that is was also never boosted past 10psi.

From what I can tell it has 1-2mm shaft play without oil. Is that bad?

Ive read that they have factory shaft play of up to 1mm so that when they heat up it still spins freely? Or is that false?

What else should I look for on the turbo to tell its condition, type?

factory shouldn't have any play, the whole turbo will heat up pretty evenly so bearing tolerances shouldn't change much

1-2mm sounds about right for a 20 year old stocker. just throw it on and fingers crossed it doesn't blow smoke

a tune would get you a bit more power but probably no more than say 10kw. it would be more responsive and better on fuel but it's up to you. Your set up is on about the limit of the stock ECU.

Actually I'm not sure about the RB20 ecu's so maybe ask someone else; but it's worth mentioning that an aftermarket ecu + tune will be minimum $1250

Without tuning you will run into the same problems as anyone else winding up the boost on an RB20 would, just at lower boost levels. The factory maps are richer and more retarded up at the the high revs and high load regions than are good for making power. The RB25 turbo pushes a bit more air at any given boost level (or more to the point, the exhaust side flows more exhaust gas at any given boost level, reducing restriction on the engine which is what allows more air to flow at the same boost, if you know what I mean). So what that means is where things might start to get a bit black smokey on an RB20 turbo at 14 psi, you may reach that sort of flow at 12 or 13 psi.

In addition, you will possibly max out the injectors in a similarly early way. It isn't wise to wind up the boost without knowing the fuel pressure stays good at high load and revs and the injectors aren't bumping up against the 100% duty cycle region.

  • Like 1

Also a little hurdle you will/may come across...

The stock 20 turbo comp housing has a nipple to read boost for the wastegate actuator. The 25 doesn't. You will need a nipple welded onto your I/C piping to complete the conversion completely.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...