Jump to content
SAU Community

Recommended Posts

  • 2 months later...

When the AWD glide was still in my car I was able to run 10.4 not using the transbrake with a real lazy footbraked 1.7 60ft launch. Tried the transbrake few times and it just spun as I didn't warm up the rear tyres in my 33GTR.

Powerglide puts the power down so smoothly compared to a manual. Defienatley had a high 9sec pass with a decent launch. Power plant was a Rb26 with hks 2530's with a manual normally make about 600awhp.

  • Like 1

When the AWD glide was still in my car I was able to run 10.4 not using the transbrake with a real lazy footbraked 1.7 60ft launch. Tried the transbrake few times and it just spun as I didn't warm up the rear tyres in my 33GTR.

Powerglide puts the power down so smoothly compared to a manual. Defienatley had a high 9sec pass with a decent launch. Power plant was a Rb26 with hks 2530's with a manual normally make about 600awhp.

Did you change back to the manual??? What happened to the box?

  • 9 months later...

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

And GTRPSI my phone app didn't let me see you post

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

Already adapted to suit the RB block bolt pattern, tranfercase and bolt straight in, considerably more than the 5K mentioned above.

Ive been looking into it.....(and still researching it)

A straight built 2spd powerglide or Turbo 400 to take serious power, yes $5K and less.

Add to that 5k for the box these parts that you will require also.

Custom length and spline output shaft to suit transfercase.

Fabricated sump to clear the drive shaft when the box is massively rotated

Suitable length and angle pick tube to put the oil filter at the bottom of the new fabricated sump.

The dip stick takes some messing around to get it at a suitable height for when the gearbox is rotated.

Decent torque converter can be $1000-2000.

Shifter

Transcooler ect ect

Pretty quickly it gets to 10-12K.

  • Like 1

Add to that 5k for the box these parts that you will require also.

Custom length and spline output shaft to suit transfercase.

Fabricated sump to clear the drive shaft when the box is massively rotated

Suitable length and angle pick tube to put the oil filter at the bottom of the new fabricated sump.

The dip stick takes some messing around to get it at a suitable height for when the gearbox is rotated.

Decent torque converter can be $1000-2000.

Shifter

Transcooler ect ect

Pretty quickly it gets to 10-12K.

Exactly, and thats assuming you know what your doing......

http://shop.quaife.co.uk/nissan-skyline-gtr-6-speed-sequential-gearbox

Chuck this beast in! Perfect daily/quarter mile monster.

Rated for a lousy 750 hp. Waste of time for a "drag car".

@Ryan, have you thought about selling the output shafts and other bits as kits for GTR owners?

That way we could build up our own strengthened autos and just add the bits on to convert them to work with the GTR transfer case.

Would save everyone a shit load of development and you could recoupe some of your already made developement costs along the way.......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...