Jump to content
SAU Community

Recommended Posts

Well i finally got a pre-tuned chip from Toshi, basically had the fuel/boost limiter and speed limiter removed.

Here are the results, i kept things pretty tame with only 10deg advanced base timing with adj pulleys set at 2deg advanced inlet and 3deg retard on exhaust.

I think i really need to invest in a PFC to straighten out my A/F ratio and get a better power curve.

let me know what you think.

Ben.

Dynosheet2.jpg

I set the ign timing really low for two reasons.

1. i have a shit timing light i cant really trust, and didnt have time to get it sorted before the dyno.

2. i wanted it to be super conservative because i plan on taking it to WSID a few times.

I will hit the dyno again and try smooth out the midrange A/F ratio with the SAFC and maybe give it a tad more timing, just so it creeps over the magical 300rwhp mark :D

I didnt get to play with my adj pulleys unfortunately. just on the setting i listed above, so i dont know the exact difference they made.

These were on my stock injectors with 2530, the first pretuned chip with high fuel pressure saw the A/F ratio up top below 10! so they can flow a fair bit.

yeah its a bloody rocket! i love it, it pulls harder than alot of GTR's i have driven so im very pleased :)

i wonder what time ill get at WSID. i really want to get into the 12's but i think i might be dreaming a little on street tyres.

but i have some soft suspension that should help.

Hi bbenny

My chip is not only fuel/boost limiter and speed limiter removed.

Its changed

HIGT octane Fuel map.

HIGT octane Ignition time map

Fuel/Ignition timing TP scale

Some cars TTP MAX

Remove speed Rev Boost Limit

With about 4000rpm the increase is 50hp thsn std ECU.

Top end about 30HP increse.

This chip is basically for all R32 mods 044 fuel pump amd GT2530 turbo .

Price only $200 inc mods ECU and chip.

If I go to dyno with you I be able to make better map for your car .

Please give me e-mail

Im sure yours should be sweet, you have all the bits on you need.

I need a PFC to straighten out my A/F ratio and should see a better curve, might give a little more timing too just so i can say i have over 300rwhp hehe

Evan, giv ethe guys at Unigroup a call and see if they will have a play with the Wolf.They have tuned a range of ecus, and when i spoke to them about 6 months ago they hadnt tried the W0lf ver 4, but were confident it woudl be easier/better to setup then Micxrotech

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...