Jump to content
SAU Community

Recommended Posts

Id probably go with tein, pretty decent for their price. Then again, i dont think it will matter when it comes to N/A skylines. You wont be having a huge amount of power to push high end coilovers to their limit, nor do i think you will be doing track days with a n/a. Id probably just go with cheapy coilovers, provided they dont bottom out and that they do their jobs on the streets, which is basically all you need (im also guessing its more of a cosmetic mod without the compromise of handling/comfort). And good on ya for not dumping them on king springs, at least someone does something right.

Edited by Deza3000

How is buying cheap coilovers better than a set of Kings low and some B6s?

"provided they dont bottom out and do their jobs on the streets" "assuming its for a cosmetic look without the compromise of handling/comfort"

I thought i implied that it still needed to do their job on the streets. It doesnt have to be over the top expensive is what im trying to say, even 2k is pushing it. Second hand HKS could even be considered cheap. And im pretty sure you and i both know that King springs on stock shocks is a pretty stupid idea, any set of coilovers would do a better job than factory worn out shocks on cheap king springs.

Who said anything about stock dampers? Not I. I specifically said Bilsteins (B6). I would guarantee you that I could get any R32 from one place in Australia to another faster and more comfortably on ~4kg/mm Kings springs and a set of Bilsteins than you could on a set of 6/4 kg/mm (or worse, the typical 8/6 kg/mm) coilovers with crappy damping. Same car, just change the suspension units.

The fact is, a set of Kings lows will drop an R32 to pretty much exactly the legal height, are the right spring rate to work well on our crappy road surfaces, are comfortable and will last a long time. Mine have been in the car for all of this century so far, and they are as good as the day they went in. The Bilstein front dampers are still going strong, about the same age. The KYBs at the rear are dying. Most of the coilover bros around here would have been through 2 or three sets in the same time if they'd kept the same car.

Tyres are stock external diameter (235/45 on 17s). So the gap you see is what you get at lowest legal height. Car went through Regency last year and was pretty close to spot on for height.\

That's more luck than good management. Sydneykid's grooved (modified) Bilsteins might be required to get an arbitrary other car to the exact right height.

post-66906-0-11610800-1392813719_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...