Jump to content
SAU Community

Recommended Posts

As for a power figure, when running 20+ psi and maxxed out i would ideally like it to make around 400kw.

But as the car will be used primarily for drifting when i drop it to the tuner (probably JEM or DVS Jez) i am just going to tell them to make it as safe as possible and i don't care how much power (within reason) has to be sacrificed. I think it should make 300kw on an ultra safe tune. Is all this possible with a Hypergear SS2?

  On 27/04/2014 at 1:12 AM, scotty nm35 said:

I'm doing this on a 2.8 atm, GTX3076 with .82 externally gated off the stock manifold. Should be very responsive.

Whats an ETA on the finish date? Is it a stroked 26 or 25? I presume you mean a standard 25 manifold.

After seeing all the RB2530 results with GT35's it has me a little nervous the old GT30 will be struggling up top.

Stroked 25, running an auto box though. He is hoping for a responsive 350kw, should probably just do 400kw on a manual car with no restrictions, you may want the 1.06 rear though, and must be external gated.

  On 27/04/2014 at 1:14 AM, iruvyouskyrine said:

As for a power figure, when running 20+ psi and maxxed out i would ideally like it to make around 400kw.

But as the car will be used primarily for drifting when i drop it to the tuner (probably JEM or DVS Jez) i am just going to tell them to make it as safe as possible and i don't care how much power (within reason) has to be sacrificed. I think it should make 300kw on an ultra safe tune. Is all this possible with a Hypergear SS2?

The SS2 won't be making 400rwkws. It will get you a super responsive 360rwkws mark on E85 fuel working with RB30det engine. You will be looking at SS3 or SS4 for some thing 400rwkws+. Also I'm not too sure how doable it is on stock manifold, might need to run a proper high mount.

  On 27/04/2014 at 11:32 AM, hypergear said:

The SS2 won't be making 400rwkws. It will get you a super responsive 360rwkws mark on E85 fuel working with RB30det engine. You will be looking at SS3 or SS4 for some thing 400rwkws+. Also I'm not too sure how doable it is on stock manifold, might need to run a proper high mount.

I thought as much. Would have been nice to crack 400 but i thought it would run out of puff. Out of your turbos what would you recommend for just being able to crack 400kw? IE what turbo would be maxing out at around 400, as most of the time i would be running much less than that and would like it as responsive as possible.

Edited by iruvyouskyrine

Currently have an RB25/30DET with ~9:1 CR CP Pistons, little to no head work done (R32 RB25DE head), with Tomei 256°/8.5mm cams. GT3076R strapped to the side of it (I bought Cubes' turbo off him!).

Car made 281RWKW @ 18 PSI on a pretty conservative dyno (Jaustech) - dyno plot is in the RB30 Dyno thread/sticky img-301131610-0001 (2).pdf

Realistically, if I had more AFM (Q45 @ 5.1V) and bigger injectors (was at about 90%) it would have hit the 300 easy with good boost control. But tbh, I didn't care about the number as all I was after was response. Makes ~220-230 RWKW @ 4000RPM which is far more than my diff and tyres can handle.

Only regret I have is not using a Neo head for the build. Would have meant I could achieve around 9:1 CR with a stock bottom end and the head is better anyway. Also would have meant I could run VCT :)

Edited by R32Abuser
  On 27/04/2014 at 11:35 AM, iruvyouskyrine said:

I thought as much. Would have been nice to crack 400 but i thought it would run out of puff. Out of your turbos what would you recommend for just being able to crack 400kw? IE what turbo would be maxing out at around 400, as most of the time i would be running much less than that and would like it as responsive as possible.

For this size engine you can run a SS-4 turbo. That maxed at 435rwkws. It is more responsive then a 3582 also.

Hi #@R32Abuser thanks for that mate :)

Sorry for this but here come the questions haha

What size rear housing is the 3076 running?

And i'm guessing it is revving to 7000 RPM?

98 or E85?

Certainly a nice looking graph either way, mine should look even better with 9.5 CR and VCT! I'm thinking i should just stop worrying about numbers and enjoy the car when it's done. I'm sure it will fry tyres just fine.

What size rear housing is the 3076 running? 0.82 Rear

98 or E85? BP98

Cutout at 7000RPM. That said the thing was starting to nose over up top anyway.

VCT would be awesome - well worth the small amount of effort. 9.5:1 is definately getting up there in terms of Static CR.

Initially, I was having big issues with the motor pinging not being able to take more than about 8 degrees of advance. I thought it was CR initially and that the builder had f**ked up. Long story short, went to another tuner and made more power and no pinging (using knock ears).

  • 1 month later...

Uppers are the way to go.

Those oil restrictors, if rebuilding i dont knock the new ones over the old, i pull the old one out, you would be surprised how much gunk collects under them, i knock the new one in after cleaning the block.

Yeah i wouldn't be surpsised to see a fair bit of stuff there after 20 years of running. Unfortunately it's too late now as the head is already on haha, this bottom end was untouched anyway. If it was doing a bottom end rebuild i would pull them out for sure!

Okay i have what is hopefully the last quiestion.

I have this from Simon that was posted in another thread

  On 17/03/2014 at 5:20 AM, Simon-S14 said:

its easy as... drop the sump, then undo the large pressure relief valve nut, inside is a spring and a ball bearing. leave them there, then get 2xm6 flat washers (i used spring washers and then bent them in vice to become flat) and place 2 of them on top of the spring and then refit the cap. reseal the sump.

should get an extra 20psi out of it.

I had my engine on a stand when i removed the relief valve. I was careful to remove the nut and spring carefully, but then as i placed them down something else fell out. It looks like a bucket type thing, will post a pic in a second. But can anyone tell me which direction and order these things go back in. Annoying because i tried hard to keep it all together i just didnt realize there was another thing in there. Also i don't know what ball bearing simon is talking about, i can't see one in there.

That looks pretty well like it. So what Simon is saying is stick your washer or two in the seat under the spring in the screw in plug. Good job so far.

Only thing I would do is add a crankcase vent off the sump somewhere (typically intake side above oil level) while the engine is outside of the car. Even if you don't use it, its there for later on.

Yeah I was sure that's the way it went back together. I added 2x M6 washers which added an extra 3mm preload to the spring.

Also got the crankcase ventilation sorted, got my sump baffled and trapdoors added. Also got 2x -10 AN fittings welded to the sump :)

post-84937-14042973476451_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...