Jump to content
SAU Community

Recommended Posts

Can't wait to see what people bring for sale, might find afew gems :)

Il be there around 7:30ish

Me too........ Make sure you come and say hello.

I'll be the old fossil there!

Bob.

Yes, please buy your tickets before the event. This is a pre-registration deal. Dealing with those that didn't follow the instructions and get their Eventbrite reg will slow things down for those that did the right thing.

Thanks.

Lol define toy will bob always good chatting to you, you bringing your ADM or vspec?

I'm bringing the V-Spec, I gave it a bath this morning, not long finished it.......

My ADM is in hibernation........

Bob.

Its on tomorrow. :-)

Wut?

Yes it's on tomorrow but you turn east onto Clyde St off Silverwater Rd > left past Wilson Pk > left under Silverwater Bridge and Voila!

Humbla starts drinking sessions early these days.

She stands up at AA meetings and proudly announces "I've been dry since leaving the pub across the road"

AA Convenor: "But that's not a pub - it's a church!"

Humbla: "Oh is that what it is? Well he's a nice man with a white collar & always serves me (at mates rates) out of a big goblet. The only complaint is that the peanuts are flat and tasteless"

  • Like 1

lol well f**k me im an idiot!

Lol i had in my head that it was today too, good thing i checked the thread before i left hahaha. I'm only 5 minutes away though, so i could have passed it off as a 'small drive'

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...