Jump to content
SAU Community

Recommended Posts

Hi Guys

testing compression on my rebuilt motor returns about 100psi across all 6, so my question is is this normal with these cams and have others experienced the same numbers

I have checked some guys having the same results but didnt find too many

did you drop the oil and see excess of fuel in oil ? (fuel running down the side of the cylinders)

A loose build i.e. large clearances. or even rings. Who did the build and how was it fired up / run in

100psi is far to low for a fresh rebuild.

Edit:

Not to cause concern, more to make you even more wary and check it out thoroughly.

I run Type B's not that that has much to do with it.

After my first build it was around 85 because the builder had made a mistake which caused a catastrophic failure.

one of the symptoms before the failure was fuel in the oil.

2nd build by CRD and is around 170 across the lot.

Have you tried 2 different gauges when measuring

Edited by Sinista32

I did the rebuild evrything was in spec initial startup was with normal mineral oil idling for about 30 min

I then drained the oil and started driving but the conditions was a bit rich and battled with tuning then after another 200km i drained the oil that was also smelling of fuel

some new oil now and smelling of fuel again after 150k

its still stock bore with stock pistons and new rings bores was honed before assembly for bedding

I wouldn't call fooked just yet. The boys on here are pretty good.

It maybe a case of pulling it out if your in doubt of any of the work.

You rebuilt with all stock internals.

Were the rings put on factory spec / positioning and double checked ?

Sitting there idling doesn't do anything for ring seal. Got to get the gases in behind the rings to push them against the bore otherwise they're just "going for the ride".

http://www.mototuneusa.com/break_in_secrets.htm

Give that a read.

^^^ What he said. It may be too late but give it a shot anyway. Drop the synthetic oil if that's what you've got and put mineral oil in. Do not labour the engine but give it plenty of welly - up to 6000 and button off and repeat. Watch for overheating and leaks and if ok continue for half an hour - then retest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...