Jump to content
SAU Community

Recommended Posts

Hi Guys

testing compression on my rebuilt motor returns about 100psi across all 6, so my question is is this normal with these cams and have others experienced the same numbers

I have checked some guys having the same results but didnt find too many

did you drop the oil and see excess of fuel in oil ? (fuel running down the side of the cylinders)

A loose build i.e. large clearances. or even rings. Who did the build and how was it fired up / run in

100psi is far to low for a fresh rebuild.

Edit:

Not to cause concern, more to make you even more wary and check it out thoroughly.

I run Type B's not that that has much to do with it.

After my first build it was around 85 because the builder had made a mistake which caused a catastrophic failure.

one of the symptoms before the failure was fuel in the oil.

2nd build by CRD and is around 170 across the lot.

Have you tried 2 different gauges when measuring

Edited by Sinista32

I did the rebuild evrything was in spec initial startup was with normal mineral oil idling for about 30 min

I then drained the oil and started driving but the conditions was a bit rich and battled with tuning then after another 200km i drained the oil that was also smelling of fuel

some new oil now and smelling of fuel again after 150k

its still stock bore with stock pistons and new rings bores was honed before assembly for bedding

I wouldn't call fooked just yet. The boys on here are pretty good.

It maybe a case of pulling it out if your in doubt of any of the work.

You rebuilt with all stock internals.

Were the rings put on factory spec / positioning and double checked ?

Sitting there idling doesn't do anything for ring seal. Got to get the gases in behind the rings to push them against the bore otherwise they're just "going for the ride".

http://www.mototuneusa.com/break_in_secrets.htm

Give that a read.

^^^ What he said. It may be too late but give it a shot anyway. Drop the synthetic oil if that's what you've got and put mineral oil in. Do not labour the engine but give it plenty of welly - up to 6000 and button off and repeat. Watch for overheating and leaks and if ok continue for half an hour - then retest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...