Jump to content
SAU Community

Recommended Posts

Hi Guys

testing compression on my rebuilt motor returns about 100psi across all 6, so my question is is this normal with these cams and have others experienced the same numbers

I have checked some guys having the same results but didnt find too many

did you drop the oil and see excess of fuel in oil ? (fuel running down the side of the cylinders)

A loose build i.e. large clearances. or even rings. Who did the build and how was it fired up / run in

100psi is far to low for a fresh rebuild.

Edit:

Not to cause concern, more to make you even more wary and check it out thoroughly.

I run Type B's not that that has much to do with it.

After my first build it was around 85 because the builder had made a mistake which caused a catastrophic failure.

one of the symptoms before the failure was fuel in the oil.

2nd build by CRD and is around 170 across the lot.

Have you tried 2 different gauges when measuring

Edited by Sinista32

I did the rebuild evrything was in spec initial startup was with normal mineral oil idling for about 30 min

I then drained the oil and started driving but the conditions was a bit rich and battled with tuning then after another 200km i drained the oil that was also smelling of fuel

some new oil now and smelling of fuel again after 150k

its still stock bore with stock pistons and new rings bores was honed before assembly for bedding

I wouldn't call fooked just yet. The boys on here are pretty good.

It maybe a case of pulling it out if your in doubt of any of the work.

You rebuilt with all stock internals.

Were the rings put on factory spec / positioning and double checked ?

Sitting there idling doesn't do anything for ring seal. Got to get the gases in behind the rings to push them against the bore otherwise they're just "going for the ride".

http://www.mototuneusa.com/break_in_secrets.htm

Give that a read.

^^^ What he said. It may be too late but give it a shot anyway. Drop the synthetic oil if that's what you've got and put mineral oil in. Do not labour the engine but give it plenty of welly - up to 6000 and button off and repeat. Watch for overheating and leaks and if ok continue for half an hour - then retest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...