Jump to content
SAU Community

Hks Pistons Noisy? 2.8 Stroker..

DannyzGTR

By DannyzGTR,
in Engines & Forced Induction

 Share

Recommended Posts

scotty nm35 Grand Master

scotty nm35

Posted
Posted

It's obviously the piston's fault, not the clearance. :P

Get on to your machinist/engine builder and ask him exactly what Piggaz asked above. My guess is he set it up loose because you want to lean on it hard, hence you will get a bit of noise.

drpheel Enthusiast

drpheel

Posted
Posted

very common for forged pistons, p2w ( piston to wall clearance ) will vary depending on the load / heat the engine will endure , Since forged piston expand with heat (more then stock) some builder will run a higher piston to wall clearance then recommended by the MFG so the piston will not hit the cyl wall when it will expand a bit more depending on the load / heat. This is what you call piston slap. It will quiet down as your car gets to operating temperature because of the expansion of the piston with the heat.

If the noise persists when hot, now that would be another issue.

I would like to know if you have the build sheet or could ask your engine builder what piston to wall clearance he is using for your aplication

Ben C34 Grand Master

Ben C34

Posted
Posted

Well the apparently hks gave pre cut rings for the 2.8 stroker kit.. I wanna hear from hks piston owners lol

I like the way you haven't answered how much piston to bore clearance you are running.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Well the apparently hks gave pre cut rings for the 2.8 stroker kit.. I wanna hear from hks piston owners lol

And aren't all piston rings "pre-cut"? They would be pretty hard to get on the pistons otherwise. Gap can only be adjusted by removing material!
GTRPSI Mentor

GTRPSI

Posted
Posted

So ask your machinist.....he set it up.

If you want to quieten it down you could always get new bigger pistons and rings and rebore/hone it correctly or friction coat the piston skirts which takes up a little clearance.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      gtr hood match gt/gtt front fenders?

      By JC71 · Posted

      would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
×
×
  • Create New...