Jump to content
SAU Community

Recommended Posts

R32 GTR / RB26 sellout

RB26 R32 GTR Long motor. Come from a car with 52,000 on the clock. Compression was 160 across the board. Comes with intake but no hotside $3200

R32 GTR 100mm Trust tube and fin intercooler with HKS hard pipe kit $1300

R32 GTR Reo trimmed to suit above cooler $150

R32 GTR Excellent condition front bar trimmed to suit above cooler. Silver $600

RB26dett HKS 2530 twin turbos. Excellent condition. $1700

RB26dett Garrett GT2560r twin turbos. Excellent condition. $850

GTR Gearbox - Push Type from car with 52,000 on the clock $600

GTR Gearbox - Pull Type $600

RB26DETT PowerFc with Hand controller $700

RB26dett Nistune ECU $450

RB26/25/20 Nismo twin plate clutch. Probably 50% meat left $700

RB26dett GT35 highmount kit, 6 boost manifold, progate 48mm, braided lines, greddy y pipe intake $2200

R33 GTR wheels with random tyres with tread $950

R34 GTR wheels wth azenis st115 tyres $1400

R32 Uncracked dash pad. No Vents $250

R32 GTR Atessa Sensor $200

RB26 Blitz oil cooler kit suit GTR $550

Engine loom suit R32 GTR $140 each (2)

Z32 afms. Genuine. with plug. $200 each (2)

RB26 coilpacks - Yellowjackets $250

Old school Greddy Profec EBC. Complete. $175

All located in Campbelltown. Sydney

Pics over the weekend

Link to comment
https://www.sau.com.au/forums/topic/444664-big-r32-gtrrb26-parts-sellout/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...