Jump to content
SAU Community

Recommended Posts

Hi forum

I purchased an SR20 a few months ago and conveniently it came with an engine stand bolted to it, awesome. Now i recently purchased an RB25 engine to start working on, however I've found the engine stand i have doesn't bolt up, and honestly doesn't seem like it could support the RB's size or weight so i've put it in a tyre which is ok for pulling the manifolds and pumps off, but not great for doing proper work to it.

Does anyone have any suggestions as to a brand or particular tool shop that will sell an engine stand that meets my needs? I've called supercheap, repco and other auto stores and they have all told me that they're not sure if it will work or not.

Any help would be greatly appreciated

Cheers

If you are anywhere in Melbourne, you can call around to my place and take mine. It held a RB25 fine, and I really don't need it anymore.

Thanks for the offer, sadly I'm in Sydney

Thanks for the help guys, you've instilled a bit more confidence in me lol - ill go grab one on my day off

Appreciate the comments and photos!

Something I found with my stands, I also didn't give it a thought when buying.

A "normal" model has 2-wheels on the back and 1-wheel on a single leg out the front.

The "heavy duty" model has 2-wheels on the back and 2-legs/wheels out the front.

The heavy duty one is a bit of a nuisance when fitting up the engine as the front legs on the engine crane exactly hit the legs on the stand. The single leg stand, not a problem.

So my normal stand does everything, heaviest engine would have been a complete 2JZ with a full Rd28 probably the same weight.

Agreed. I never put any thought into it. Just buy one.

3 leggers work fine too.

Comes down to the gauge of steel used and welding.

I have 2 with 3 legs, one i bought 32 years ago for V8 builds, thick as anything, craps all over all the 4 legged ones ive seen that are from China.

RBs may not be heavy, but the fact they are long adds weight over the end thats not tied down, in the end there is more force than some V8s on the stand.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...