Jump to content
SAU Community

Recommended Posts

  • 4 months later...
5 hours ago, R377 said:

 

not sure what you mean Johnny ?

 

Referring to the caliper adapter kits.  Alpha Omega?

Good to see steady progress and sensible upgrades with your car.

Hopefully there's a proper diff centre on the horizon?  1.5 way at the very least, but don't be afraid to go with a 2 way.  Massive improvement when incorporated with a HICAS lock bar.

22 hours ago, Dale FZ1 said:

Referring to the caliper adapter kits.  Alpha Omega?

Good to see steady progress and sensible upgrades with your car.

Hopefully there's a proper diff centre on the horizon?  1.5 way at the very least, but don't be afraid to go with a 2 way.  Massive improvement when incorporated with a HICAS lock bar.

 

 

Oh yes i forgot about that.  Johnny talked me into getting a proper lsd.  I went with a Nismo GT Pro 2-way.  Pricey but very good under load and under brakes

  • Like 1
  • 2 weeks later...
On 11/10/2017 at 11:52 AM, ActionDan said:

Check your:

Ride height at each corner - uneven heights = uneven corner weights and more likely to lock one side. 

Toe/Camber - Less tyre contact patch = more lock up. 

 

thanks for that, i didn't even think about that.  I think one side of the car is slightly higher with the coilovers

On 11/8/2017 at 8:18 AM, Dose Pipe Sutututu said:

Oooo I see Intima pads :)

How do you find the Type-D?

 

I can't really say as i went from stock brakes with qfm pads to evo's 350mm front and rear with intima d - type track pads. It would the equivalent of dicking Margaret Thatcher to dicking Jennifer Hawkins....

Evo brakes are just soo good i got travel sick with them !!!

  • Like 1
  • 4 weeks later...

 

Just did a compression test - all cylinders were 150-160 which i am well happy with...

 

reference service. 14mm sump plug.  16mm spark plug. plug 4 is a bit tricky to get to, have to remove a 10mm bolt to get the right angle on it

NGK 7121     BCPR6ES-11 plugs

  • 1 month later...

Looking around for new tyres - Nankang AR-1 looks to be popular.  They only do a 295 or a 265 tyre for the rear.  I pulled the hell out of my rear guard and tried on a 295 with my 10+38.  It just fit inside by about 7-8mm with about 2 degrees of rear camber and i had about 12-15mm on the outside :) I dumped my car, now on big bumps and driveway the inside of the back rim scrapes on the inside.

I was thinking of going a 10.5 wheel.  They make a +35 offset in a 10.5 wheel. It will sit 3mm inside and 9mm outside.  I am not too sure about this. Would need a 5mm spacer and that would take it to 14mm wider to not make it scrape.  Either that or pull the ride height up....hmm. Maybe ill have to play around with the tyre calculator

https://www.wheel-size.com/calc/?wheel1=295-30-18X10ET38&wheel2=295-30-18X10.5ET35&fcl=50mm&wcl=30mm&scl=50mm&sr=0mm

going from 10+38 to a 10.5 +35 with the 295 tyre i tried on, the wheel is 3mm closer and will stick out 9mm further, the tyre. Tyre will stick out 3mm further which would be ok.

To run a 5mm spacer on that 10.5 wheel

https://www.wheel-size.com/calc/?wheel1=295-30-18X10ET38&wheel2=295-30-18X10.5ET30&fcl=50mm&wcl=30mm&scl=50mm&sr=0mm

wheel will sit out 14mm further and tyre would stick out 8mm further...That would be good, the wheel would sit more flush with the guard.

So i might need to look for a lightweight wheel that is 10.5 +30 to +35 offset ? any suggestions ? im looking at the new enkei rs05rr but i would need to run a 5mm spacer with that at a minimum

 

With the fronts they do a 245/40 which is a balloon but they do a 255/35 which sat nice and low profile.  I have a 9.5 +15 with 235 on the front with -3 camber and it does touch the guard but i haven't got stuck into pulling the guard out yet.

I was wondering if i could fit a +22 to +25 wheel with a 255 tyre on the front ? There is about 25mm on the inside but i haven't turned the wheel yet.  Wondering if i could fit a 255 and still be low ?

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...