Jump to content
SAU Community

Recommended Posts

So I priced up some BC Golds for $1495NZD, plus $500NZD for the certification to make them legal, when I found some Jamex springs for $299NZD delivered that will give me a 40mm drop.

The seller (Jamex NZ) says there are no problems with using these as they are legal (no cert needed, direct replacement etc) and are fine with standard shocks - even saying they have never had issues with any of their springs being used on standard height shocks.

I understand the attraction of coilvers, but I don't think I NEED that kind of adjustability. I just don't wanna wreck my ride or injure anyone by using lowering springs alone.

Are they really that bad?

P.S. At $400+ a corner to replace only the shocks(KYB) it is worth going to coilovers, but only if I need to replace them.

OEM shocks can be had for significantly less than $400 per corner!

Think amayama.com or similar.
I can possibly get information for you as someone just purchased a swag of OEM suspension components (including all 4 shocks) and the total was just over $700 delivered.

What is involved in the Certification for Coilovers? Is this for some kind of external/independant testing?

I'm curious, as the main stumbling block to engineering BC coilovers in NSW (Australia) is the absence of material data & testing info from the parent manufacturer.
If I had this kind of information; I could provide it to an engineer, and he'd be happy to sign them off.

OEM shocks can be had for significantly less than $400 per corner!

Think amayama.com or similar.

I can possibly get information for you as someone just purchased a swag of OEM suspension components (including all 4 shocks) and the total was just over $700 delivered.

What is involved in the Certification for Coilovers? Is this for some kind of external/independant testing?

I'm curious, as the main stumbling block to engineering BC coilovers in NSW (Australia) is the absence of material data & testing info from the parent manufacturer.

If I had this kind of information; I could provide it to an engineer, and he'd be happy to sign them off.

Getting a cert is easy (all my mods are certed/legal) but it costs around $550 so you tend to do it once for all the mods.

Over here the cert process is remarkably sensible.It is run by the Low Volume Vehicle Technical Association (not a government body) . Certifiers have a lot of discretion and although there is a guide manual which mandates some things much is left up to their experience and knowledge. For example they will pass Cusco camber arms but not some of the dodgy cheapo versions although there is not a list of approved arms as such.

OEM shocks can be had for significantly less than $400 per corner!

Think amayama.com or similar.

I can possibly get information for you as someone just purchased a swag of OEM suspension components (including all 4 shocks) and the total was just over $700 delivered.

Checked out amayama.com, and at $196USD per corner I'm looking at $922NZD plus shipping and 15% GST - call it an even $1200 plus springs and coilovers become a real possibility :whistling:

Checked out amayama.com, and at $196USD per corner I'm looking at $922NZD plus shipping and 15% GST - call it an even $1200 plus springs and coilovers become a real possibility :whistling:

Let me find out for you;there is a cheaper way.

I got Jamex lowered springs for my ARX and no problem with it. I bought it from Auckland.

Did you get them from the listing on TradeMe?

Let me find out for you;there is a cheaper way.

Don't rush, I don't need shocks. I just wanna lower my car and will use lowering springs unless they ruin my shock, at which stage I'll either replace or go coilovers.

The only way they will damage your shock is if you go too low, the actual shock will top out and crap around the top. I have seen this happen to an old set that I used 40mm lowered springs then cut 2 coils off, this was done for shits and giggles on an old cortina that we used as a paddock/dirt racer and we had it in that car for about a year and a half.

I lowered my 180 on Tein lowering springs and the shocks were fine for a couple of years. I finally replaced them with Bilstein coilovers for track work. I actually preferred the ride comfort on the road with just the lowering springs.

- Lance

Different car but still relevant, I had lowered King Springs with standard shocks on my R34 GTT for about a year and the ride quality was ... shocking (pardon the pun). Very crashy. The shocks also started leaking before long as they operated outside the designated area with the lowered springs. So in short, if you're going lower springs, get shorter shocks to match, to maintain ride quality.

I ended up going BC BR's with custom (softer) spring rates and difference with night and day, so much better than the OEM+King combo. I priced up a set of aftermarket shocks only, to go with the Kings, and they weren't much cheaper than the BC's...

Just my $0.02

  • Like 1

Keep the OEM shocks and get Lucas springs and you will be fine.

Ask a professional steering and suspension shop the part number, buy & install them your self and then take it back and get it aligned properly.

About $550 all up. $210 F/R pairs each and $85 for an alignment.

Ride remains almost the same (slightly stiffer) ride height less. Win/Win

Edited by Sinista32

No one has mentioned that if you're getting stiffer springs, the shocks aren't designed for them. You'll notice when going over a bump or a ditch it will be firmer on the compression but spring back quicker when the spring is released from its downward stroke. The standard shocks aren't designed to have that much force pushing on them

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...