Jump to content
SAU Community

Turbo Flutter/plumb Back

BatmanBarrie
 Share

Recommended Posts

BatmanBarrie Rookie

BatmanBarrie

Posted
Posted

I know this is a really controversial topic but being new to owning a turbo car that turbo flutter sounds cool and makes an impression to me and my friends. I've lots of mixed replies when I've asked people how to get a flutter. One friend told me ''Buy an aftermarket BOV and make sure its plumb back!'' But then another friend told me "You can't buy plumb back BOV's and to take it to a workshop and ask them to put a line on it back to the air filters/AFM." Can you guys help me out?! I know some people will say '' Have fun rebuilding your engine in a few years. '' But it's a personal choice and i would really appreciate the help!

Link to comment
https://www.sau.com.au/forums/topic/445948-turbo-flutterplumb-back/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

It won't wreck the engine. Could potentially wreck the turbo which then might decide to fly through your engine. Being that the exhaust wheel is the weak wheel it's more likely to die but still

It may not happen. But still

Flutter works best with no BOV (flange blanked off) or any BOV with an adjustability that's set to very hard. Atmo BOV'S will screw up the way the car runs too and won't be recommended by anyone on here

  • Like 1
Deza3000 Proficient

Deza3000

Posted
Posted

The flutter you speak of is compressor surge. That SUTUTUTU sound is because aftermarket bovs have STIFFER springs to prevent boost leak. The stiffer springs can also cause the bov to not open at all, causing the air to rush back throguh the turbo, giving that famous ricey VSHHHSUTUTUTUT.

If you want the flutter, take out your blow off valve, and put it in reverse, so the valve never opens, or just block off the BOV all together. You should now hear some significant fluttering.
If you want a louder flutter, install a POD filter, that shizz amplifies induction and flutter sounds. Want it even more louder? Get a steal intake pipe, then you'll hear it from down the street.

That being said, compressor surge sucks lol. And its a massive cop magnet. Provides no performance benefits, unless your BOV is leaking on high boost. If anything, it provides negative effects such as premature wear on your turbo.

Dose Pipe Sutututu Grand Master

Dose Pipe Sutututu

Posted
Posted

^ why is that each time I put in the word "tttuuurrrkeyyy" it gets replaced with rubbish? lol

Flutters are sick.. if you don't like it - put a stock airbox on.. then when you're bored back off it goes :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...