Jump to content
SAU Community

Recommended Posts

R33's have a double latched setup from factory... you could pull the bonnet release cable at 200kph and it wouldn't fly open...
Of course you're more than welcome to make your own additional restraint with a carrabeana and a loop of wire to secure it further.

Edit: I would be running the additional if I had an aftermarket bonnet, carbon fibre, bracing removed, or something like that which could allow the bonnet to flex more than normal

Well bugger me... I come back after a day and have to cater for a few more!
BBQ for Members:
Tony +1
John P
Simon
Anna & Luke
Paul S
Michael +1
Jamie
Owen
Dave
Allan
Matt L
Snowy
Gorjan
Chris T
Richo
Pete
Jamie L
Jamie G +1
Lebo Luke
Mark
Matt B
dan.1337


Total - 26 people

Is there ANYONE else??? Given it's a pretty hefty increase in numbers already
  • Like 1

Hi guys, I have been reading the supp regs and the cams manual and just want some help with one thing.

Do I need to run an extra bonnet restraint cable or is the factory latch ok??

Cheers

Luke

You should be ok, a long as it has the two methods of fastening.

They can be a bit picky on after market bonnets though.

Not required. Just eat and be merry.

Squires Loft Nunawading is supplying the food at cost and cooking/extras for free. In return SAU-Vic picks up the raw food bill on members behalf as it's a Members Only BBQ - one of the many member perks!

Great too see so many faces around.

Yes I did try and remove the speed limiter from the Evo. Only to have the battery go flat...

The speed limiter is gone now and car working fine. (Frkn Evo's)

Thanks too Squires for the food, amazing as always.

Not sure what others thoughts were, but this day ran better than previous days of late.

Bearing in mind a wrx dumped oil and some chev driver painted the armco.

There is a discussion in the champ thread about the 30th of August at Winton. Get in there and have ur say.

Not sure what others thoughts were, but this day ran better than previous days of late.

Obviously gutted for members with day ending issues

But yeah, excellent day, started to run so quickly at the end that my car couldn't take it anymore and I believe quite a few were setting PBs etc, big crowd, excellent food - missus complaining I'm getting fed to well, what diet :-)

Was a much better day, even if i didn't make full use of it. Some minor attention this week and I'll be sorted. :)

100 cars, awesome. 120+ cars, shithouse.

Day was run perfectly compared to the other 4 rounds so far this year, which the oversubscribed side was pretty much the cause.

Let's hope it continues!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...