Jump to content
SAU Community

Recommended Posts

I got my genuine Nissan idler bearing bolt and this is the first thing I see.

The runout of the last thread looks pretty nasty, lots of grooves (stress risers).

Has anyone else got a new idler bearing bolt to see if it is like mine?

Maybe post up a picture?

post-8140-0-86093900-1407136010_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/446413-rb-idler-bearing-bolt/
Share on other sites

It's not a bolt that needs to be super tight so will not be a problem at all.

If it was a torque to yield bolt you might be concerned but not for an idler bolt that is only tight not stetched.

  • Like 1

Can't believe there was a thread made for this.......

You dont use the last thread

There is only about 20ish Nm of torque on the nut

I've seen worse, People re-use these without problems

Honestly. If it is worrying you that much, Just buy another one, They arent expensive

  • Like 1

Can't believe there was a thread made for this.......

You dont use the last thread

There is only about 20ish Nm of torque on the nut

I've seen worse, People re-use these without problems

Honestly. If it is worrying you that much, Just buy another one, They arent expensive

I know what is wrong with the bolt, I was curious if other people had noticed the same thing.

Just because you don't use that section of the thread doesn't mean its not doing anything. Its actually doing alot more than the threads that are engaged.

Torque for that bolt is 43 - 58Nm and it is in single shear.

I am buying another one.

Some suggested reading material.

http://www.engr.sjsu.edu/youssefi/me154/notes/Bolt%20failure.pdf

http://arp-bolts.mobi/p/tech.php?page=2

Remember that the stud/nut are clamping the stationary part of the bearing

My comment about the nut not using that part of the thread was more about - your not going to make the thread any worse, then say if you ran a nut over it and damaged either the thread on the nut or stud. I'm fully aware of how forces are applied on bolts/studs

I was only saying, I can't see a major fault with the thread from the photo, maybe its the way the flash has gone off but it doesnt look that bad at all to me. And there is always chances of minor defects in a manufacturing process. And for the sake of a $2 part.......

As for your reading material, don't assume people are clueless when you dont know what they do for a living.

  • Like 1

Quite a long time back there was a spate of engine failures due to breaking of the idler bolt.

I spoke with Gary Cook regarding better quality bolts as the stocker isn't anything out of the box.

Gary had bought a selection of Nissan studs and the quality control was appalling.

Plenty of Unbrako quality to choose from but they don't fit under the cover, head is a bit too long.

Then almost overnight, no more breakages of the stock stud.

So were owners over tightening the stud or perhaps the belt, or did Nissan improve their quality control??????

The cross section there looks to be a fair bit bigger than in the next valley where the thread is fully formed, and those scratch marks dont appear to deep. So it doesn't look too scary to me, but i've never looked that closely before. :unsure:

My method of installing bolts.

Does this bolt fit? > Yes > put it in and tighten it to FT spec

> No > don't use it

Do I have another one that fits? > Yes > Use that one then

> No > ......where did I put my tap and die kit....

Edited by iruvyouskyrine

I am buying another one.

It's your bolt. If you don't like it and don't want to use it get another one.

Think you may have skipped a post there.

I am just curious to see what other peoples thoughts are.

It turns out it's to hard to show fine detail in a picture and very few people actually understand how surface finish can affect the life of something is under stress, so hopefully this thread can educate some people.

Here is another excellent article, scroll down to Surface Roughness

http://www.efunda.com/formulae/solid_mechanics/fatigue/fatigue_factor.cfm

I believe you are over thinking the whole thing. I would use it unless the picture doesn't show some horrible defect.

It looks pretty standard like marks from the machines used to roll or cut the thread

Edited by 89CAL

The threads are rolled, very poorly I might add. The finish indicates worn forming tools. I can say this due to experience in manufacturing head studs.

So, back to my original question.

Has anyone else got a new idler bearing bolt to see if it is like mine?
Could you please post up a close up picture?

I'm not interested in anyone's opinion, that's not what I am asking for. I am asking for a picture of the threads.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...