Jump to content
SAU Community

Recommended Posts

I know this topic has been beaten to death numerous times but I just wanted an experienced opinion on what weight of oil you guys would use in my car.

Its an r32 gtr 94 model with about 130k kms on the clock and no serious mods (basically stock). Now seeing as factory weight is 7.5-30, in your opinions would you guys go full syn 5w-30 or 10w40?

Link to comment
https://www.sau.com.au/forums/topic/447348-weight-of-oil-for-r32-gtr/
Share on other sites

As the engine wears the clearances get larger. To maintain decent oil pressure a thicker oil would be required.

Do you have an oil pressure gauge? How is the oil pressure now? If it's fine jeep using whatever you are using.

Yeh on the factory oil press gauge it sits about half way when driving and drops a bit on idle but I've heard that the factory one can be a bit dicky sometimes.

I think I will go the thicker then.

Also do you know of the sump capacity by any chance?

AFAIK the only good reasons to run a thicker than specified oil is to;

1. Return oil pressure to spec on a worn motor,

2. Provide a safety margin in a motor that is overheating the oil,

3. Make an engine run more quietly, however, higher noise does not appear to correspond to higher wear

I run Mobil 1 0W-40 in my Stagea daily and in my street, but tracked, GTR. IMO its a good bang for buck oil. In the stag its still good after 6000kms so ill try 7000kms and re-test this fill. I will test the GTR @5000kms next change.

On a stock motor a ?W-30 should be fine as long as the oil pressure is within spec.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...