Jump to content
SAU Community

Duncan's Race Car - The Most Overdue Build Thread On Sau


Recommended Posts

  • 1 month later...

so that reminds me of the old joke....

what's yellow and purple and has 13 nipples?

yes, a bloody gtr race car.

over the last few weeks the focus was getting Neil's radical running for the first round of the hillclimb champs,  which we just managed (well, I did a bit but f**k all overall). but in any case I hadn't touched my car since mid jan until the other day.

so I spent the weekend bleeding stuff, 4 calipers with 2 nipples each, abs with 2 nipples, attessa with 2 nipples, and the strangely uni-nippled clutch. looks like I've got good pressure in all of them now but it's hard to be certain until it drives.

I haven't got the car started yet, I tried both the Haltech and the PFC and it cranks but doesn't run. The PFC continually resets so I assume it's a problem with the ECU power (i removed the ECCS relay).  Time is a bit tricky at the moment because we are moving to the country, eating a lot of peaches, but I'm still hoping to get it running first.

 

Have you thought to rule out the power issue to give it direct power?

This also brings me back to when you rewired Neils car, from memory you had the same problem and found that there was a second power wire that had been disconnected. That raise any memories? Or am I just going mad? ha ha

PS: If it still doesn't start I have a hammer you may borrow ;)

you're spot on Matt, that's why I'm going down the dangerous path of assuming that same symptom means same problem.  In the gtst (which had always run fin on the stock computer), when we put a powerFC in we had put a fuse into an existing but empty circuit in the fuse box. Without it the PFC constantly reset, with it in it worked perfectly.

I'm getting the same symptom here so I'll just start with checking the various 12v wires in the engine loom have power when they are meant to....if it's the only mistake I've made after this much rewiring I'll be surprised.

  • Like 2

well, I made a little progress.

first up I worked out an issue with the ECU wiring; basically IGN signal in a 32 goes from the key to the DS firewall grommet to the front engine bay fuse box to the stock boost controller (of all things), around the front of the engine bay, along the strut tower, through the PS firewall grommet and into the ECU.  All of which would be fine if I hand't assumed that only the boost controller used that source in my car now and wired it to the boost controller switch.  So for now boost has to be on either high or low for the ECU to receive the IGN signal and start up properly.

So that got the powerfc behaving properly, but despite some further stuffing around the car still doesn't start. I then plugged the haltech back in (properly this time) to check everything there (it shows way more inputs and sensors) but I still couldn't work out the issue and decided to give up and take it to someone who knows what they are looking at. I expect to post up again afterwards saying I was out of fuel or something stupid like that.

Anyway, so I focused on the next step instead, getting the car rolling again. Wheels are on, brakes working, everything tightened up (oh except the front driveshafts, and all the ball joints which I better remember....). She's back on the ground, rolling, and godzilla approves

gtr-has-landed.jpg

  • Like 1

so anyway, the next (actually final) big job of the reco is painting the interior and fixing the exterior. And no I'm not trying DIY, I've done that before (on the nugget) and it looked really shit.  I'm not trying to make a showcar but I do want it tidied up.

so back out with everything in the interior, wiring, seatbelt mounts and eye bolts, boot release, gear shift etc, looking really empty, again

empty-again.jpg

Next up is vaccum then wipe down with wax and grease remover, then tape up and ship it off to the painter.

Also need to remove all the stickers, even the ones that have been on there for 10 years and will pull the paint off because I'm getting them to clean up the outside as well

I decided to move onto the painting now, because in big news for us, we've bought a place outside Sydney near Goulburn and are selling our current place over the next few months.  I really needed the car rolling and OK to move so I decided to get it ready for painting instead of trying to spend weeks on the ECU.

  • Like 1
20 hours ago, Duncan said:

....................................

I decided to move onto the painting now, because in big news for us, we've bought a place outside Sydney near Goulburn and are selling our current place over the next few months.  I really needed the car rolling and OK to move so I decided to get it ready for painting instead of trying to spend weeks on the ECU.

Bought near Goulburn eh, Wakefield Park?

  • 1 year later...

So I can't claim to be moving quickly (but then again this build never has....) but the car is in the paint shop now.

Initially they thought they were going to just even up the current surface a bit and respray it....I did warn them this was the 4th time the car had been painted.

As you can see, after they got started and saw what they are in for, they are taking most of it back to bare metal to prep, prime and paint. Car should be about 50kg lighter now too.

gtr-paint1.jpg

Also fixed the small modification I made against the bank at Targa High Country.

gtr-paint2.jpg

They are doing inside and out, should be back in a few weeks. The only real challenge has been the front windscreen which is pretty much irreplaceable being one of Dell's heated ones. They are very nervous about taking it out knowing how hard and expensive it would be to replace....

  • Like 3
  • 3 weeks later...

Well I haven't yet seen how the car turned out, because Kel and I borrowed a dirty evo and went and did Targa Tas last week.  We took "Lucky" the evo which has all sorts of problems each time she competes but never fails to finish. In our case it blew a cooler pipe about 1klm into a 25klm stage turning it into a mirage instead of an evo for the next 10 minutes, but otherwise it did well.  We ended up 8th in Early Modern and would have been 5th without the cooler pipe issue which is OK for a pretty rookie driver (although the nav was awesome all through).

The main thing I remembered from doing Targa High Country a few years back was that tyre wear can be a killer, so I tried to minimise it

saving-tyres1.jpgsaving-tyres2.jpgsaving-tyres3..JPGsaving-tyres4.jpgsaving-tyres5.jpgsaving-tyres6.jpgsaving-tyres7.jpg

Oh, and well done to Liam and Larry for second in Early Modern.....great effort for the week :)

  • Like 8
  • 6 months later...

So, Kel is off rallying again and I thought if I don't do some work on the car it may not just finish itself....

The car is back from paint and there is no longer any evidence of that small issue on the nav side where the road was a little narrow that the driver thought.  They've painted the inside too so it's time to put the wiring back in.

Did some more labelling of the wire because I hadn't finished them all

wiring-labelling.jpg

Ran the wiring to the back of the car

wiring-rear2.jpg

And into the boot. That would have all been done back there but the shop didn't attach the rear bar properly so its off again for now

wiring-rear1.jpg

Also go the main/dash wiring mostly sorted.  The smartwire is mounted on rubber mounts to help keep it alive longer.

wiring-dash1.jpg

Mounted it up

wiring-dash2.jpg

All the wiring back in and connected up on the middle and driver's side. Looks like a damn mess but its actually pretty sorted, most of the hanging stuff is for dash and switches

wiring-dash3.jpg

Still have work to do on ECU mounting and wiring on that side. Maybe another 6 months. Or tomorrow.

  • Like 1

So, got a bit more done today.

Since I've gone haltech I need to mount a heap of little boxes.  So back in the day the fabricator made up an MDF dummy but I needed to do it in carbon fibre (becaues race car)

wiring-ecu-1.jpg

 

So, taped up the cf sheet and copied across the pointswiring-ecu-2.jpg

 

A little hacksawing and drilling, and it looks like this.  Again I've used rubber mounts to insulate the electronics a little from race car bumps

wiring-ecu-3.jpg

Mounted up in place in the passenger footwell, tucked up behind the roll cage, all wiring in.

wiring-ecu-4.jpg

That's pretty much it for now

wiring-ecu-4.jpg

I also mounted up all the rest of the interior wiring; rallysafe, GPS for dash, camera, intercom all in.

Unfortunately the next step is to redo the dash, since the last one had an uncovered trailer/truck related issue which made it flatter than it needs to be. I also have to put a big more wiring back in underneath (main fuel pump, fuel pressure and e85 sensors, o2 sensor) and a bit in the engine bay too...then it should be right to put the battery back in and see what I've done wrong in the wiring...

 

  • Like 6

Great to see you are making progress buddy, pity your 3.5 hours away or I would help.

Post some pics of her painted please.

Funny enough, I had a shit day at work and thought I would read your whole thread, cheered me up, thanks.

Cheers

 

  • Like 1

Thanks Troy. Did I see right that you took yours to Bathurst the other week? Must have been fun, and plenty of space to let it stretch it's legs there....

Anyway, here's some exterior pics....keeping in mind it's had 15 years of racing and rallying so like most race cars it is only expected to look good from a distance.....

I think it is bright enough, should be easy to spot in a carpark, and come up well in pics/tv

repainted-2.jpg

repainted-3.jpg

repainted-1.jpg

Didn't get a lot done this weekend as I was out fighting blackberries again.  Just sorted the engine bay wiring but needed to get it up on stands to deal with the wiring in the inner guard and under the rear. The quick jacks are a good thing but not really that quick (a bit fiddly to get right) and mega heavy to move

  • Like 4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...