Jump to content
SAU Community

Recommended Posts

Hello

Today I noticed a hairline crack at the base of the radiator filler neck, it trickles a small amount of coolant when driving and for a short while after until the car cools down. it's not losing heaps of coolant but don't want to be driving and have it open up and lose my coolant I'm not going to drive it until it's sorted in case it goes bang big crack.

Just looking at advise as to what I should do,

Is it worth removing the stock one and taking it to a radiator place and get the top tank replaced? $150-250

Or buy a brand new koyorad oem replacment radiator $250 http://www.ebay.com.au/itm/RADIATOR-NISSAN-SKYLINE-R33-R34-93-2001-MANUAL-VEHICLE-KOYO-RADIATOR-/200449233351?pt=AU_Car_Parts_Accessories&hash=item2eabb491c7

The car is used 99.5% on the street so a big expensive racing radiator would be overkill and unnecessary. And don't want a cheap china alloy one either

Anyone been here before what would be the best way to go?

Link to comment
https://www.sau.com.au/forums/topic/450995-radiator-hairline-crack/
Share on other sites

Buy a new one. Fix it now and it might just break in another spot later.

Get a new alloy radiator now and less likely to have problems in the future. I bought a Greddy radiator when mine split. Best thing I think I could have done

Buy a new one. Fix it now and it might just break in another spot later.

Get a new alloy radiator now and less likely to have problems in the future. I bought a Greddy radiator when mine split. Best thing I think I could have done

Yeah I'll get a new one, not really keen on replacing the top tank idea.

I've looked the Blitz 41mm alloy rad and koyo alloy 53mm they are 500-600$ Not sure if it's overkill and a waste of money. Do these fit like oem?

Genuine Nissan.

What do these cost? Couldn't find anything online not sure if anywhere would have one and be able to have it to me within a week

This is dodgy as but I had a mazda bravo way way back when and the top tank split the whole lenght, being young and broke I pulled out the aerodite and put a healthy coat over it till I could afford a new one, 4 years later I replaced it cause it looked dodgy not cuss it was leaking :/

  • Like 1

Solder up the crack or just get a replacement stock radiator from your local shop. It should last another 15 years. I just use stock radiators in my car with the RB30 and it doesn't overheat on track days.

This is dodgy as but I had a mazda bravo way way back when and the top tank split the whole lenght, being young and broke I pulled out the aerodite and put a healthy coat over it till I could afford a new one, 4 years later I replaced it cause it looked dodgy not cuss it was leaking :/

Just fixed a Cracked Honda S2000 Gearbox case that cracked around the drain plug in 3 places (told son not to overtighten it 1000 times before putting the plug back in and what does he do?) with JB Weld. :)

I have heard people are also using it on radiators, but i can tell you his gearbox is not leaking and it saved me from pulling the box out and getting it welded back up again. (or replacing the box)

Dodgy as hell but it worked, dont know about the next gearbox oil change though......

The radiator top tank is plastic remember.

I was advided against repairing it when mine cracked. Especially if you are happy to just to get a cheaper than Jap brand radiator. Sounds like it will be fine for what you need. If you want to spend some money than the Greddy radiator is great. Fits perfectly and shroud fits on nicely

Really up to you but

I'm going to replace the radiator hoses to, would it be a good idea to replace the thermostat while I'm there?

The radiator top tank is plastic remember.

I was advided against repairing it when mine cracked. Especially if you are happy to just to get a cheaper than Jap brand radiator. Sounds like it will be fine for what you need. If you want to spend some money than the Greddy radiator is great. Fits perfectly and shroud fits on nicely

Really up to you but

The only Greddy radiator I can find online is $1099.!?

Would there be any cooling issues with the koyo oe replacment? Anyone used one?

I'm going to replace the radiator hoses to, would it be a good idea to replace the thermostat while I'm there?

The only Greddy radiator I can find online is $1099.!?

Would there be any cooling issues with the koyo oe replacment? Anyone used one?

If you have the standard clutch fan and shroud (assuming fan works fine), you're better off getting something that can use the shroud.

http://www.perfectrun.jp/src/quick/qui_home.php?qui_cb=101&qui_cmd=cg101008_10102&qui_cpb=0&qui_cat[]=sct_502&submit=GO

Take your pic, then either buy through there, RHDJapan, Import Monster, Nengun, or Jesse Streeter.

The radiator top tank is plastic remember.

I was advided against repairing it when mine cracked. Especially if you are happy to just to get a cheaper than Jap brand radiator. Sounds like it will be fine for what you need. If you want to spend some money than the Greddy radiator is great. Fits perfectly and shroud fits on nicely

Really up to you but

The top tank in my Bravo was plastic and it held up for 4 years with aerodite :)

Just looked like arse :/

If you have the standard clutch fan and shroud (assuming fan works fine), you're better off getting something that can use the shroud.=sct_502&submit=GO]http://www.perfectrun.jp/src/quick/qui_home.php?qui_cb=101&qui_cmd=cg101008_10102&qui_cpb=0&qui_cat[]=sct_502&submit=GOTake your pic, then either buy through there, RHDJapan, Import Monster, Nengun, or Jesse Streeter.

Are these instock in aus or need to be sent from japan?

They all say factory air duct cannot be used with this radiator. I'm still using factory airbox is this a problem

What about fenix rads http://www.ebay.com.au/itm/Nissan-Skyline-R33-R34-93-02-Heavy-Duty-Alloy-Fenix-Radiator-/171117111768?pt=AU_Car_Parts_Accessories&hash=item27d75fe9d8 they look quality?

Are these instock in aus or need to be sent from japan?

They all say factory air duct cannot be used with this radiator. I'm still using factory airbox is this a problem

What about fenix rads http://www.ebay.com.au/itm/Nissan-Skyline-R33-R34-93-02-Heavy-Duty-Alloy-Fenix-Radiator-/171117111768?pt=AU_Car_Parts_Accessories&hash=item27d75fe9d8 they look quality?

They get shipped from Japan.

You should be concerned about the shroud more than the air duct, but if you want to keep the duct, get OEM.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...