Jump to content
SAU Community

Recommended Posts

Hi guys,

Not long ago I started to hear some rear awful noises coming from the rear of my car - back left. I thought it was just the normal clunking from the welded diff I had put on there years ago.

I decided to jack up the rear left and see if any wheel studs were loose but it wasnt, what I did notice was that I was able to wobble the wheel slightly even thought it was perfectly flat against the hub. So started to trying to move parts at the subframe to see if anything was lose. I discovered that I was able to push the rear left long black column that attached itself to the diff and rear hub left and right. I tried to do the same with the right side, but it wouldnt budge.

I believe my rear left wheel's ability to rock slightly is related to that long column's freeplay.

My question is can I just change this out and replace it or does it should like something else. At first, I thought perhaps my diff was stuffed - the noise when you drive gets louder and more unbearable like bolts/nuts being crushed - ie welded diff?? Or is my wheel bearing causing this, although Ive watched clips on youtube on wheel bearings being stuffed and mine doesnt make a humming sound it makes a clunking and clanking sound that increases with speed.

Pleaes help.

Attached the the long black coluum I am referring to.

Thanks,

Nozila

post-1473-0-07150900-1418883669_thumb.jpg

  • Like 1

That "long column" is a driveshaft. Calling a "roundy-roundy bit" might have been more accurate.

See the big ends on it? With the rubber boots? Those are CV joints. One or both of them are probably rooted. You either need a new driveshaft or replace the CVs. New driveshaft may be secondhand. To remove it, simply undo the 5 bolts on the diff end flange of it and it will slide out of the hub. Take it it a CV/driveshaft specialist for fixing or take it to a wrecker to get an equivalent 2nd hand, or take it to a mechanic for a proper diagnosis in case I have mistakenly internet diagnosed it.

  • Like 1

Thanks for that. Unlikely to be rooted diff? When I move slowly, it doesnt clunk. I recall my sister's mazda 2 had bad cv joint up front and it would only make noises when turning whilst with mine it mines it moving when moving. Anyways, I will remove the driveshaft and have it looked at.

Thanks for the input

The CV is on a spline and should be able to move slightly in and out and IMO not likely your issue

Although being able to "wobble the wheel slightly" if bolted on tight would concern me ever so much

Also clunking/banging is usually a sign of dead shockies, is it worse when you drive over bumps ?

What exactly are you doing when you hear said noises ?

Hi,

Yes that's a r31 subframe I think-I was just using the pics as a reference to indicate the part that is moving. I had thought it was my coil overs as well so I checked them and they are bolted in fine. It clunks and what sounds like pots and pans banging each together which is why I'm asking if that is the sound a rooted diff makes. I'll try to go through a process of elimination by changing out the driveshaft first. Perhaps the noise is made by the wobbly rear left as when in motion, the noise increases which is understandable but I don't know why it would sound like metal-thumping and clinking yes but not sound of metal pots and pans.

Thanks for everyone's opinions so far

I think Mick is referring to the shocks internals not the fixing points to the car, having had a completely dead shock in a previous car I would have to agree, but it was only on bumps, i.e. activating the shocks. on smooth roads it was fine.

  • Like 1

Makes the noise on smooth roads, bumps or not.

So I think I can rule out the shocks? I am going to jack up the car from the diff, put it in neutral and spin the rear wheels to see if I can replicate the noise. If I cant, hopefully that can rule out the diff being shoot and allow me to focus on the freeplay I have in the rear left and movement in the driveshaft on the left that goes into the diff housing.

Going to take car down to suspension specialist on Tues.

I did jack up the car and tried to move wobbly the rear left and sure enough it did-wheel hub seems loose. Right side had no wobblys whatsoever. Put it into first and you can hear it vibrant and clunk.

thanks, I thought in my head it might be a wheel bearing but wasnt 100% sure. Going to see how much the suspension shop is going to charge otherwise I'll take it down to my family mechanic to replace for me - driving the distance there is going to create some unbearable noises.

Update guys, I just asked suspension place how much it cost to replace my wheel bearing and was quoted $625 for supply of bearing, fit and alignment. Is that quite high or within the ballpark?

It's been a while since I got anyone to serviced by anyone but myself.

Hope you are sure it's the bearing!

I'm not certain for 33 gtst, but for 32 gtr they are available from Nissan only ~350 trade price. So 300 to R & R is reasonable considering the work involved.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...