Jump to content
SAU Community

Recommended Posts

  • 2 months later...

been looking around but couldn't find information on this

does anyone know if half height EV14 injectors with height adapter will fit the r34 GTT?

reason i ask is the r34 GTT uses 3/4 height injectors but the plug sits really close to the plenum, looking at the 1/2 height injectors i have sitting around i'm a bit worried that it won't fit

or will it be ok if i spin the injector around so the plug faces downwards to give it more space?

secondly, the bosch injectors I've got do not have lower O rings, they've got one of those square section rubber seats like those on the GTR, like this:

https://www.efihardware.com/products/1489/injector-lower-square-section-seal-large

Do I have to convert this to O ring so it will seal properly?

just needed to make sure before i start to gather the parts and pull things apart

You are making this harder than it needs to be.

PM scotty nm35 and tell him what you want.

Don't ask questions. Just do what Ben said and be done with it. Scotty will give you the right injectors are the right price.

Yeah I know it's not something most people do when they change injectors. I would have contacted Scotty for a set of 3/4 height ones if I don't already have these half height injectors lying around taken out of my old car. I'm just seeing if anyone has done this before, if not it's ok I'll just have to trial fit it first to see what I need

Edited by chiksluvit

I assume you have 14mm 1/2 length injectors? I can supply the height adapters if you need them. Do you have the plug adapters?

Should just drop into a 34 with the correct adapter to make them 3/4 length. If the injectors have been laying around a while I would be a little worried, enough to get them cleaned/tested anyway.

Without seeing a pic I have no idea, but it isn't 14mm now is it. I assume the lower retainer for the oring has been modified to fit the square Oring, but you should be able to get a 14mm Oring to seal without falling off. PM me if you need some.

Notice there is nothing to stop the Oring falling off anymore? It has been chopped off to accommodate the new square GTR Oring. I can supply the round 14mm Orings but they may slide around and fail to seal in the plenum properly I guess.

Not the lower tip part, the part where the Square Oring is at the moment. The standard Oring will fit back on, it will just slide around now the captive plastic part is gone.

  • 4 months later...

Are these what are referred to as the ID1000? In the below link..

What is the best price you're all getting your 750-1000cc r34gtt injectors for?

Are the below suitable and is this a good price?

http://m.ebay.com.au/itm/6-x-1000cc-Bosch-E85-FG-XR6-turbo-upgrade-fuel-injectors-0280158040-/151333893801

No they are not ID1000s. ID stands for Injector Dynamics which is a crowd that takes standard Bosch EV14 injectors and mods them. There are other vendors doing the same thing. This eBay vendor appears to be doing the same thing, only these are effectively "no-name". They might be fine. They probably are fine. But they are not ID.

If you want our recommendation, just ask Scotty.

Machining the little holes on the tip of the injector can help with a bit of extra flow through them, except in the case of the injectors you linked. With them it makes no difference.

How critical is 1% flow to you? What if it was 10% less on one cylinder, what do you think the outcome would be?

Bosch tell me there can be up to 10% flow difference with the new e85 injectors, similar to the older 2000's.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...