Jump to content
SAU Community

Recommended Posts

Slight modification to the calendar, comments please. Good or bad?

We would like to change this to the 14th of March with Circuit Club, comments please.

Round 2

Sunday, 29 March 2015

Winton

AROCA

Hit the apex (driver training) & maximum laps (experienced drivers) event, passenger laps all afternoon

Saturday, 4 April 2015

Sandown

SAU VIC

Happy with any Sandown track day as it's so close to home :)

  • Like 1

Slight modification to the calendar, comments please. Good or bad?

We would like to change this to the 14th of March with Circuit Club, comments please.

Round 2

Sunday, 29 March 2015

Winton

AROCA

Good. Much prefer the idea of doing Winton with Circuit Club rather than AROCA. Others won't like that it is on F1 Saturday but I don't get given corp tickets so really couldn't care less hehe.

Remembering that we'll be dropping at least 2 rounds this year to make up the final results. So people who want to GP Saturday, just make it one of your drop rounds.

It's a compromise, but for the opportunity to cut some laps with your Friends and Family in the passenger seat or get some skills training. I think it's worth it.

  • 2 weeks later...

Hi guys,

I'm new to the page and I just signed up as a state member so just a quick question am I aloud to jump on track on the 8th or do I have to go to a few meetings first?

Also how do the cams licensing work?

Cheers Jake!

you will need to apply for a CAMS LS2 license to participate in any of the motorsport rounds. all the information is on the cams website.

Our next monthly meet will be covering whats involved to get on the track, so may be worth checking out. you dont have to come to any meets prior to a track day, but certainly helps with recognising some faces

  • Like 1



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...