Jump to content
SAU Community

Recommended Posts

Josh at Forge Performance is helping me out, i want it done properly, especially with the throttle body rework and resealing the plenum properly as well as the hoses.
hes a champ and looks after pricing really well so im happy to use his assistance.

pin hole leak in one of the pipes... it let out sooooo much coolant lol

all fixed.

must say, she does seem to be in good company at FP

1511648_895896273803954_4276019161622516

also... mmmmm sexy wrinkle paint for the plenum

20150511_131856_zpsygyi8tx9.jpg



20150511_131717_zpsml8wyfqg.jpg


blasted back to bare metal and refinished.

I think the intake side needs greddy hard-pipes and all new metal IC pipes all done the same?

then a deep candy red for the rockers and cam cover, neaten it all up a bit.

the old paint, like all, was cracked and flaking off, looked a bit shitty.

20150118_131742_zps1s7zubke.jpg

Edited by GH05T
  • Like 1
  • 5 weeks later...

haha,
well picked up a gtr passenger seat last night and i have a fixed bride drivers seats arriving hopefully this week. ill get be a gtr back seat from a mate when i go to the hills next and it will look a bit better.

  • Like 1

lol, i put the passenger seat in yesterday but it needs a good clean, will do as a place holder untill i track down a mint one. more delays in my bride seat turning up but ill have both in soon, Josh at forge is gonna hook me up with a gtr rear too

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...